/ADL/LP/.../

Trend IQ22x Controllers
Accessories

Auto Dial Lite integral modem for IQ22x series



/DP/

Trend 2 Line Display Panels

The Display Panel enables the user to view and adjust selected parameters within an IQ22x controller. It provides all the facilities necessary for the operation of a stand-alone building control system. Four programmable buttons make commonly used values available by single key selection. The Display Panel is an option which may be integrally mounted in an IQ22x controller (DP
The integral 2 line display panel is only available with IQ22x controllers eg. IQ221/UNB/DP/230
2 x 40 character back-lit display
4 programmable buttons
Allows monitoring and adjustment of plant parameters, occupation times and calendars
Allows viewing of controller alarm log
Model: integral to IQ22x


2RM/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: 2 Relay Module


2SRM/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: 2 Single Relay Module


2VID/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: 2 Voltage to Current Driver


3RM/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: 3 Relay Module


3XTEND/EINC L/230

Trend Network Cards Ethernet

The 3xtend/EINC L enables IQ networks running on the IQ System current loop Lan, Ethernet, and LON to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EINC, Ethernet Internetwork Node Controller, provides the means by which the Building Management System network can incorporate an Ethernet network. The EINC operates at the internetwork level, including the necessary support for WANs (e.g. TMN support). It also provides virtual CNCs which allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EDS-205 and EDS-305-M-SC are industrial 5-port Ethernet switch that supports IEE 820.3/820.3u/820.3x with 10/100M, full half duplex, MDI/MDIX autosensing RJ45 ports. The EDS-305-M-SC also has a built in relay warning function which alerts maintainers when power failures or port breaks occur and is equipped with 4 10/100T(X) ports and 1 single mode 100baseFX port, SC connector. Both devices operate over a wide temperature range and are DIN rail mounting, making them ideal for most industrial environments.
The IMC-101-M-SC,which has been designed for stable operation in industrial environments, provides conversion between 10/100BaseT(X) and 100 BaseFX. It rated to operate at temperature ranging from 0 - 60oC, and is DIN rail mounting, making it ideal for most industrial environments.

EINC Cards
Model: Ethernet INC with LON
Network: TCP/IP + LON + Trend LAN
Power: 230Vac
Comments: IP40


3XTEND/EINC L/24

Trend Network Cards Ethernet

The 3xtend/EINC L enables IQ networks running on the IQ System current loop Lan, Ethernet, and LON to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EINC, Ethernet Internetwork Node Controller, provides the means by which the Building Management System network can incorporate an Ethernet network. The EINC operates at the internetwork level, including the necessary support for WANs (e.g. TMN support). It also provides virtual CNCs which allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EDS-205 and EDS-305-M-SC are industrial 5-port Ethernet switch that supports IEE 820.3/820.3u/820.3x with 10/100M, full half duplex, MDI/MDIX autosensing RJ45 ports. The EDS-305-M-SC also has a built in relay warning function which alerts maintainers when power failures or port breaks occur and is equipped with 4 10/100T(X) ports and 1 single mode 100baseFX port, SC connector. Both devices operate over a wide temperature range and are DIN rail mounting, making them ideal for most industrial environments.
The IMC-101-M-SC,which has been designed for stable operation in industrial environments, provides conversion between 10/100BaseT(X) and 100 BaseFX. It rated to operate at temperature ranging from 0 - 60oC, and is DIN rail mounting, making it ideal for most industrial environments.

EINC Cards
Model: Ethernet INC with LON
Network: TCP/IP + LON + Trend LAN
Power: 24Vac
Comments: IP42 NEMA3R


4DIX/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Input Modules
Product description: 4 Digital Input Expander


6RM/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: 6 Relay Module


916MDS

Trend Mobile Display Software

The 916 runs on a Microsoft Pocket PC, providing an interface to the IQ system enabling monitoring and adjustment of parameters within IQ and IQL controllers. It can be connected to the IQ network via a standard network connection (local supervisor port or CNC2), via a modem, or over Ethernet. A GSM phone may be used instead of a modem.
Access to parameters in IQ, and IQL controllers
Simple adjustment of module parameters
Graphs
Display of alarms
GSM compatibility
Product description: 916 Mobile Display Software; Pocket PC Based


962xx/UP/963xx

Trend 963 Supervisor
Upgrades

Upgrade from 962 to 963



963 FAST TRAK/CONVERTER

Trend 963 Supervisor
Upgrades

963 Fast Trak converter



963L/CD

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: no
Comments: stand alone


963L/LNC2

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: LNC2
Comments: stand alone


963L/NBOX/CNC2

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: NBOX/CNC2
Comments: stand alone


963L/SEC/CD

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: no
Comments: stand alone


963L/SEC/CD/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: no
Comments: stand alone


963L/SEC/LNC2

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: LNC2
Comments: stand alone


963L/SEC/LNC2/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: LNC2
Comments: stand alone


963L/SEC/NBOX/CNC2

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: NBOX/CNC2
Comments: stand alone


963L/SEC/NBOX/CNC2/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: NBOX/CNC2
Comments: stand alone


963L/SEC/SMS/CD

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: Secure / SMS
Serial comm.: no
Comments: stand alone


963L/SEC/SMS/LNC2

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: Secure / SMS
Serial comm.: LNC2
Comments: stand alone


963L/SEC/UP/963L/SEC/SMS

Trend 963 SMS
Upgrades

Upgrade from 963L/SEC to 963L/SEC/SMS



963L/SEC/UP/963S/SEC/3USER

Trend 963 Secure
Upgrades

Upgrade from 963 Secure Lite to 963 Secure Server (with 3 client licences)



963L/SMS/CD

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: no
Comments: stand alone


963L/SMS/LNC2

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: LNC2
Comments: stand alone


963L/SMS/NBOX/CNC2

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: NBOX/CNC2
Comments: stand alone


963L/SMS/UP/963S/SMS/3USER

Trend 963 SMS
Upgrades

Upgrade from 963L/SMS to 963S/SMS with three client licences



963L/SNMP/SMS/CD

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SNMP / SMS
Serial comm.: no
Comments: stand alone


963L/SNMP/SMS/LNC2

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SNMP / SMS
Serial comm.: LNC2
Comments: stand alone


963L/SNMP/UP/963L/SNMP/SMS

Trend 963 SMS
Upgrades

Upgrade from 963L/SNMP to 963L/SNMP/SMS



963L/SNMP/UP/963S/SNMP/3USER

Trend 963 SNMP
Upgrades

Upgrade from 963L/SNMP to 963S/SNMP with 3 client licences



963L/UP/963L/SMS

Trend 963 SMS
Upgrades

Upgrade from 963L to 963L/SMS



963L/UP/963L/SNMP

Trend 963 SNMP
Upgrades

Upgrade from 963L to 963L/SNMP



963L/UP/963S/3USER

Trend 963 Supervisor
Upgrades

Upgrade from 963L to 963S



963S/CD/3USER

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: no
Comments: web server 3 user


963S/LNC2/3USER

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: LNC2
Comments: web server 3 user


963S/NBOX/CNC2/3USER

Trend 963 Supervisor

The 963 is a powerful, real time user interface for the building control system. It enable the user to monitor plant or building services, and makes changes to the way the building is controlled from a graphical display.


Serial comm.: NBOX/CNC2
Comments: web server 3 user


963S/SEC/CD/3USER

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: no
Comments: web server 3 user


963S/SEC/CD/3USER/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: no
Comments: web server 3 user


963S/SEC/LNC2/3USER

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: LNC2
Comments: web server 3 user


963S/SEC/LNC2/3USER/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: LNC2
Comments: web server 3 user


963S/SEC/NBOX/CNC2/3USER

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.


Model: Secure
Serial comm.: NBOX/CNC2
Comments: web server 3 user


963S/SEC/NBOX/CNC2/3USER/TRAIN

Trend 963 Secure

963 Secure assists with compliance to FDA regulation 21 CFR Part 11: 963 Secure has a number of security features that provide compliance with the American pharmaceutical bodies regulation 21 CFR Part 11. 963 Secure provides maximum protection for the data it stores, and the system it is controlling. 963 Secure imposes a strong password regime, which requires the user to regularly change their password to prevent it becoming known to others.

With 2 day Secure operator training course
Model: Secure with Training
Serial comm.: NBOX/CNC2
Comments: web server 3 user


963S/SEC/SMS/CD/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: Secure / SMS
Serial comm.: no
Comments: web server 3 user


963S/SEC/SMS/LNC2/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: Secure / SMS
Serial comm.: LNC2
Comments: web server 3 user


963S/SEC/UP/963S/SEC/SMS/3USER

Trend 963 SMS
Upgrades

Upgrade from 963S/SEC to 963S/SEC/SMS



963S/SEC/UP/nn/xxUSER

Trend 963 Secure
Upgrades

963 Secure Server additional client licences (nn=existing number xx=required number)



963S/SMS/CD/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: no
Comments: web server 3 user


963S/SMS/LNC2/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: LNC2
Comments: web server 3 user


963S/SMS/NBOX/CNC2/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SMS
Serial comm.: NBOX/CNC2
Comments: web server 3 user


963S/SMS/UP/nnUSER/xxUSER

Trend 963 SMS
Upgrades

Additional Client licences (nn=existing number xx=required number)



963S/SNMP/CD/3USER

Trend 963 SNMP

In addition to the standard features of the 963 Supervisor, 963 SNMP enables the retransmission of business effecting alarms from a Trend system to IT monitoring systems, thereby reducing the down time on the IT data operations.
Model: SNMP
Comments: web server 3 user


Serial comm.: no


963S/SNMP/LNC2/3USER

Trend 963 SNMP

In addition to the standard features of the 963 Supervisor, 963 SNMP enables the retransmission of business effecting alarms from a Trend system to IT monitoring systems, thereby reducing the down time on the IT data operations.
Model: SNMP
Comments: web server 3 user


Serial comm.: LNC2


963S/SNMP/NBOX/CNC2/3USER

Trend 963 SNMP

In addition to the standard features of the 963 Supervisor, 963 SNMP enables the retransmission of business effecting alarms from a Trend system to IT monitoring systems, thereby reducing the down time on the IT data operations.
Model: SNMP
Comments: web server 3 user


Serial comm.: NBOX/CNC2


963S/SNMP/SMS/CD/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SNMP / SMS
Serial comm.: no
Comments: web server 3 user


963S/SNMP/SMS/LNC2/3USER

Trend 963 SMS

963 SMS Direct is an optional feature associated with the 963 Supervisor. It enables the 963 to automatically send alarm messages directly to a GSM mobile phone - without the need for pager bureaus or SMS gateways.


Model: SNMP / SMS
Serial comm.: LNC2
Comments: web server 3 user


963S/SNMP/UP/963S/SNMP/SMS/3USER

Trend 963 SMS
Upgrades

Upgrade from 963S/SNMP to 963S/SNMP/SMS



963S/SNMP/UP/nn/xx/USER

Trend 963 SNMP
Upgrades

Additional Client licences (nn=existing number xx=required number)



963S/UP/963S/SMS/3USER

Trend 963 SMS
Upgrades

Upgrade from 963S to 963S/SMS



963S/UP/963S/SNMP/3USER

Trend 963 SNMP
Upgrades

Upgrade from 963S to 963S/SNMP



963S/UP/nn/xxUSER

Trend 963 Supervisor
Upgrades

Additional Client licences (nn=existing number xx=required number)



ACC/24VAC

Trend IQ3 Web Enabled Controllers
Accessories

230/24 Vac, 24 VA, transformer for IQView4, with surface mounting lugs, and through earth (ground) connection



ACC/24VAC

Trend IQ3 Integration Controllers
Accessories

230/24 Vac, 24 VA, transformer for IQView4, with surface mounting lugs, and through earth (ground) connection



ACC/24VAC

Trend IQ3 Trend LAN BACnet Controllers
Accessories

230/24 Vac, 24 VA, transformer for IQView4, with surface mounting lugs, and through earth (ground) connection



ACC/24VAC

Trend IQ3 BACnet Integration Controllers
Accessories

230/24 Vac, 24 VA, transformer for IQView4, with surface mounting lugs, and through earth (ground) connection



ACC/DF

Trend Plant Temperature Sensors (NTC10k)
Accessories

Duct flange for the TB/TI



ACC/EM3/ODIN/PANELKIT

Trend Electricity Meter, ThreePhase Pulse
Accessories

Optional mounting kit for panel mounting of EM3/ODIN meters



ACC/FC

Trend Frost protection thermostats
Accessories

Optional fixing clips for T/FS



ACC/FS

Trend Plant Temperature Sensors (NTC10k)
Accessories

Mounting kit for the T/TFR-4



ACC/Flange/12mm/5

Trend Plant Humidity Sensors
Accessories

Pack of 5 clamps for HT Duct



ACC/HTD/FILTER

Trend Plant Humidity Sensors
Accessories

Pack of 5 filters for HT Duct



ACC/HTO/FILTER

Trend Plant Humidity Sensors
Accessories

Pack of 5 filters for HT Outside



ACC/NX/RS232PC

Trend Inverters 1,1..110kW, IP54


NX to PC 1.5 m cable (to connect to PC running NC software tools)



ACC/NXL/FILTER/FR2-3

Trend Microdrives IP20
Accessories

Filter for frame sizes MF2 or MF3



ACC/NXL/MF2DIN

Trend Microdrives IP20
Accessories

Kit to mount NXL frame size MF2 on DIN rail.



ACC/NXL/RS232PC

Trend Microdrives IP20
Accessories

NXL to PC cable (also requires use of RS232 adaptor below)



ACC/RS232/ADAPTOR

Trend Microdrives IP20
Accessories

NXL RS232 adaptor for use with NXL to PC cable



ACC/SMBOX/16/10

Trend IQ251 Controllers
Accessories

16mm surface mount box for RD, Box of 10



ACC/SP

Trend Pressure, Current sensor, Liquid
Accessories

Steam Pigtail for use with steam or water above 85 oC



ACC/UF

Trend Plant Temperature Sensors (NTC10k)
Accessories

Universal Fixing Clip (retrofit to existing pockets)



ACC/VSD2H/DOOR MOUNTING

Trend VSD2H Variable Speed Drivers for HVAC applications, 1,1..160kW, IP21/IP54,
Accessories

VSD2H Door panel kit



ACC/VSD2H/GRAPHIC DISPLAY

Trend VSD2H Variable Speed Drivers for HVAC applications, 1,1..160kW, IP21/IP54,
Accessories

VSD2H Advanced Commissioning Keypad



ACC/VSD2H/HAND HELD KIT

Trend VSD2H Variable Speed Drivers for HVAC applications, 1,1..160kW, IP21/IP54,
Accessories

VSD2H Hand-held panel kit



ACC/VSD2H/TEXT DISPLAY

Trend VSD2H Variable Speed Drivers for HVAC applications, 1,1..160kW, IP21/IP54,
Accessories

VSD2H Replacement Text Keypad



ACC/VSD2H/USB-PC/CABLE

Trend VSD2H Variable Speed Drivers for HVAC applications, 1,1..160kW, IP21/IP54,
Accessories

VSD2H PC Adaptor Kit - USB adaptor cable



ACCA-AD2034-SW2

Trend Actuator for Damper, 20/34 Nm
Accessories

End switch kit, with 2 SPDT freely adjustable end-switches.



ACCA-AL06-SW

Trend Actuator Linear 600N 20mm
Accessories

Dual end switches SPDT, adjustable (250 V~, 10 A) for AL0620-P models.



ACCA-AL18-SW

Trend Actuator Linear 1800N 20mm
Accessories

Dual end switches SPDT, adjustable (250 V~, 10 A)



ACCA/VB/ADK

Trend Actuator Linear 300N 6.5mm
Accessories

AL0306 to VB valve adaptor (5 off)



ACCV-5585100

Trend Valve, Short stroke, zoning, 2-port
Accessories Conex sealing

Commissioning Caps for V58* and VS58* series valves (Pack of 10)



ACCV-TC-15

Trend Valve, PN16, 2-port, Externally threaded
Accessories

Internal threaded fitting for DN15 valve pipe size Rp 1/2"



ACCV-TC-20

Trend Valve, PN16, 2-port, Externally threaded
Accessories

Internal threaded fitting for DN20 valve pipe size Rp 3/4"



ACCV-TC-25

Trend Short stroke, Valve, PN16, 2-port
Accessories

Internal threaded fitting for DN25 valve pipe size Rp 1"



ACCV-TC-32

Trend Short stroke, Valve, PN16, 2-port
Accessories

Internal threaded fitting for DN32 valve pipe size Rp 1 1/4"



ACCV-TC-40

Trend Short stroke, Valve, PN16, 2-port
Accessories

Internal threaded fitting for DN40 valve pipe size Rp 1 1/2"



ACCV-TC-50

Trend Valve, PN16, 2-port, Externally threaded
Accessories

Internal threaded fitting for DN50 valve pipe size Rp 2"



ACCW/CONFIGKIT

Trend Wireless Receiver
Accessories

Programming kit for XW/R/IQ including connection cable between receiver, PC, and supply, and CD containing configuration software



ACCW/FK/SS

Trend Wireless Receiver
Accessories

Stainless steel wall bracket for mounting XW/R/IQ at a distance of 28 cm from wall



ACCW/RW/IQ

Trend Wireless Receiver
Accessories

Wireless sensors repeater



AD05-230

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 1 square meter
Power supply: 230Vac
Control input signal: 2-pt
End switches: no
Runtime: max. 110s;50Hz
Torque: 5Nm
Damper area: 1m2


AD05-24

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 1 square meter
Power supply: 24Vac
Control input signal: 2/3-pt
End switches: no
Runtime: 110s;50Hz
Torque: 5Nm
Damper area: 1m2


AD05-24-SW2

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 1 square meter
Power supply: 24Vac
Control input signal: 2/3-pt
End switches: 2
Runtime: 110s;50Hz
Torque: 5Nm
Damper area: 1m2


AD05-P

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 1 square meter
Power supply: 24Vac
Control input signal: 0/2..10V=;2/3-pt
End switches: no
Runtime: 90/110s;50Hz
Torque: 5Nm
Damper area: 1m2


AD05-P-SW2

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 1 square meter
Power supply: 24Vac
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Runtime: 90/110s;50Hz
Torque: 5Nm
Damper area: 1m2


AD10-230

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 2 square meters
Power supply: 230Vac
Control input signal: 2-pt
End switches: no
Runtime: max. 140s;50Hz
Torque: 10Nm
Damper area: 2m2


AD10-24

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 2 square meters
Power supply: 24Vac
Control input signal: 2/3-pt
End switches: no
Runtime: 110s;50Hz
Torque: 10Nm
Damper area: 2m2


AD10-24-SW2

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 2 square meters
Power supply: 24Vac
Control input signal: 2/3-pt
End switches: 2
Runtime: 90/110s;50Hz
Torque: 10Nm
Damper area: 2m2


AD10-P

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 2 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Runtime: 110s;50Hz
Torque: 10Nm
Damper area: 2m2


AD10-P-SW2

Trend Actuator for Damper, 5/10 Nm

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
removable wiring box for direct wiring to and from controller
rotation direction selectable by switch
adjustable mechanical end limits included
24 Vac models also suitable for 24 Vdc
Built in rotation limiter: yes
Manual operation: yes

For damper area of up to 2 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Runtime: 110s;50Hz
Torque: 10Nm
Damper area: 2m2


AD20-230

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 4 square meters
Power supply: 230Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


AD20-24

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 4 square meters
Power supply: 24Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


AD20-P

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 4 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=
Built in rotation limiter: yes
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 20Nm
Damper area: 4m2


AD34-230

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 6 square meters
Power supply: 230Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2


AD34-24

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 6 square meters
Power supply: 24Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2


AD34-P

Trend Actuator for Damper, 20/34 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
rotation direction selectable by switch
when power is removed, the actuator remains in position
removable wiring box
actuator supplied with complete package mounting parts
for modulating control models: control input signal can be voltage or current
for modulating control models: autoadapt dipswitch; with this function the full span of the control input signal will be used for the applicable angle or rotation
Manual operation: yes

For damper area of up to 6 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=
Built in rotation limiter: no
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 34Nm
Damper area: 6m2


ADAPTOR BLUETOOTH/IQ22x-ADL

Trend Bluetooth Adaptor

The Trend Bluetooth Supervisor Port Adaptor enables SET or 916 to interrogate and configure the Trend Building Management System using wireless communication. It is designed to provide a temporary connection for commissioning purposes.The Bluetooth adaptor plugs into an IQs local supervisor port, or a CNC2s RS232 port, and will communicate with any Bluetooth enabled laptop or handheld computer. Additional adaptor cables are available for use with older IQs or CNC2s.
Simple wireless connectivity
Walk around commissioning
Enables PCs with only a USB port to be used for commissioning (via USB/Bluetooth adaptor)
No separate power supply required (powered from IQ with correct adaptor cable)

Adaptor Cables
Model: Adaptor cable to IQ22x-ADL supervisor port


ADS10-230

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 1.5 square meters
Power supply: 230Vac
Control input signal: 2-pt
Position feedback: no
Runtime: 45s;50Hz
Torque: 10Nm
Damper area: 1,5m2


ADS10-24

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 1.5 square meters
Power supply: 24Vac
Control input signal: 2-pt
Position feedback: no
Runtime: 45s;50Hz
Torque: 10Nm
Damper area: 1,5m2


ADS10-P

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 1.5 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=;3-pt
Position feedback: 0..10V=
Runtime: 90s;50Hz
Torque: 10Nm
Damper area: 1,5m2


ADS20-230

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 4 square meters
Power supply: 230Vac
Control input signal: 2-pt
Position feedback: no
Runtime: 45s;50Hz
Torque: 20Nm
Damper area: 4m2


ADS20-24

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 4 square meters
Power supply: 24Vac
Control input signal: 2-pt
Position feedback: no
Runtime: 45s;50Hz
Torque: 20Nm
Damper area: 4m2


ADS20-P

Trend Actuator for Damper, Springreturn, 10/20 Nm

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
rotation direction selectable by flipping the actuator 180o around its vertical axis
actuator supplied with complete package mounting parts
autoadapt dipswitch, with this function the full span of the control input signal will be used for the applicable angle or rotation
actuators come with detachable wiring box
actuator can be locked and manually wound
Spring return: yes
Manual operation: yes
Spring return timing: 20s

For damper area of up to 4 square meters
Power supply: 24Vac
Control input signal: 0/2..10V=;3-pt
Position feedback: 0..10V=
Runtime: 90s;50Hz
Torque: 20Nm
Damper area: 4m2


AL0102-24

Trend Actuator Linear 90N 2.5mm

Electrical actuator floating control, for valve series: VS58..
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Stem force: 90N
Power supply: 24Vac
Control input signal: 3-pt
Stroke: 2,5mm
Runtime: 57s
Cable length: 0,9m


AL0206-230-K

Trend Actuator Linear 180N 6.5mm

Electrical actuator for valve series: V58..
Protection class: IP43/IP42
Position indication: with red indicator
Reversible control action with AL0206-P-K.
Stem force: 180N
Stroke: 6,5mm
Runtime: 150s


Power supply: 230Vac
Control input signal: 3-pt
Manual operation: yes
Cable length: 1,5m


AL0206-24

Trend Actuator Linear 180N 6.5mm

Electrical actuator for valve series: V58..
Protection class: IP43/IP42
Position indication: with red indicator
Reversible control action with AL0206-P-K.
Stem force: 180N
Stroke: 6,5mm
Runtime: 150s


Power supply: 24Vac
Control input signal: 3-pt
Manual operation: no
Cable length: 1,5m


AL0206-24-10M

Trend Actuator Linear 180N 6.5mm

Electrical actuator for valve series: V58..
Protection class: IP43/IP42
Position indication: with red indicator
Reversible control action with AL0206-P-K.
Stem force: 180N
Stroke: 6,5mm
Runtime: 150s


Power supply: 24Vac
Control input signal: 3-pt
Manual operation: no
Cable length: 10m


AL0206-24-K

Trend Actuator Linear 180N 6.5mm

Electrical actuator for valve series: V58..
Protection class: IP43/IP42
Position indication: with red indicator
Reversible control action with AL0206-P-K.
Stem force: 180N
Stroke: 6,5mm
Runtime: 150s


Power supply: 24Vac
Control input signal: 3-pt
Manual operation: yes
Cable length: 1,5m


AL0206-P-K

Trend Actuator Linear 180N 6.5mm

Electrical actuator for valve series: V58..
Protection class: IP43/IP42
Position indication: with red indicator
Reversible control action with AL0206-P-K.
Stem force: 180N
Stroke: 6,5mm
Runtime: 150s


Power supply: 24Vac
Control input signal: 0/2..10V=
Manual operation: yes
Cable length: 1,5m


AL0306-230-K

Trend Actuator Linear 300N 6.5mm

Electrical actuator floating control, for valve series: SV16..
Protection class: IP43/IP42
Position indication: with red indicator
Stroke: 6,5mm
Runtime: 150s
Cable length: 1,5m


Stem force: 300N
Power supply: 230Vac
Control input signal: 3-pt
Manual operation: yes


AL0306-24

Trend Actuator Linear 300N 6.5mm

Electrical actuator floating control, for valve series: SV16..
Protection class: IP43/IP42
Position indication: with red indicator
Stroke: 6,5mm
Runtime: 150s
Cable length: 1,5m


Stem force: 300N
Power supply: 24Vac
Control input signal: 3-pt
Manual operation: no


AL0306-24-K

Trend Actuator Linear 300N 6.5mm

Electrical actuator floating control, for valve series: SV16..
Protection class: IP43/IP42
Position indication: with red indicator
Stroke: 6,5mm
Runtime: 150s
Cable length: 1,5m


Stem force: 300N
Power supply: 24Vac
Control input signal: 3-pt
Manual operation: yes


AL0306-P-K

Trend Actuator Linear 300N 6.5mm

Electrical actuator floating control, for valve series: SV16..
Protection class: IP43/IP42
Position indication: with red indicator
Stroke: 6,5mm
Runtime: 150s
Cable length: 1,5m


Stem force: 300N
Power supply: 24Vac
Control input signal: 0/2..10V=
Manual operation: yes


AL0406-P-K

Trend Actuator Linear 400N 6.5mm

Electrical actuator modulating control, for valve series: SV16..
Protection class: IP54
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6,5mm


Power supply: 24Vac
Power loss action: no
Manual operation: yes
Runtime: 15s
Spring return: no


AL0406-P-SU

Trend Actuator Linear 400N 6.5mm

Electrical actuator modulating control, for valve series: SV16..
Protection class: IP54
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6,5mm


Power supply: 24Vac
Power loss action: stem retracts
Manual operation: no
Runtime: 60s
Spring return: yes


AL0620-230-K

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm


Power supply: 230Vac
Control input signal: 3-pt
Power loss action: no
Manual operation: yes
Runtime: 1,0min
Spring return: no
Position feedback: no


AL0620-230-SD

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 230Vac
Control input signal: 3-pt
Power loss action: stem extends
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: no


AL0620-230-SU

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 230Vac
Control input signal: 3-pt
Power loss action: stem retracts
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: no


AL0620-24-K

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm


Power supply: 24Vac
Control input signal: 3-pt
Power loss action: no
Manual operation: yes
Runtime: 1,0min
Spring return: no
Position feedback: no


AL0620-24-SD

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 24Vac
Control input signal: 3-pt
Power loss action: stem extends
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: no


AL0620-24-SU

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 24Vac
Control input signal: 3-pt
Power loss action: stem retracts
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: no


AL0620-P

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm


Power supply: 24Vac
Control input signal: 2..10V=
Power loss action: no
Manual operation: no
Runtime: 1,0min
Spring return: no
Position feedback: 2..10V=


AL0620-P-K

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm


Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 1,0min
Spring return: no
Position feedback: 2..10V=


AL0620-P-SD

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: stem extends
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: 2..10V=


AL0620-P-SU

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm

Spring return
Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: stem retracts
Manual operation: yes
Runtime: 1,8min
Spring return: yes
Position feedback: 2..10V=


AL0620-P-X-K

Trend Actuator Linear 600N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate
End switches: optional
For modulating control models:
stem position at control signal loss is selectable: closed, half open or open (except AL0620-P)
the control action is reversible
Stem force: 600N
Stroke: 20mm


Power supply: 24Vac
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 0,5min
Spring return: no
Position feedback: 2..10V=


AL1820-230-K

Trend Actuator Linear 1800N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open.
Stem force: 1800N
Stroke: 20mm
Manual operation: yes
Runtime: 1,9min


Power supply: 230Vac
Control input signal: 3-pt
Position feedback: no


AL1820-24-K

Trend Actuator Linear 1800N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open.
Stem force: 1800N
Stroke: 20mm
Manual operation: yes
Runtime: 1,9min


Power supply: 24Vac
Control input signal: 3-pt
Position feedback: no


AL1820-P-K

Trend Actuator Linear 1800N 20mm

Electrical actuator for valve series: V16.., V25.. with 20 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open.
Stem force: 1800N
Stroke: 20mm
Manual operation: yes
Runtime: 1,9min


Power supply: 24Vac
Control input signal: 0/2..10V=
Position feedback: 2..10V=


AL1838-230-K

Trend Actuator Linear 1800N 38mm

Electrical actuator for valve series: V16.. with 38 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open
Stem force: 1800N
Stroke: 38mm
Manual operation: yes
Runtime: 3,5min


Power supply: 230Vac
Control input signal: 3-pt
Position feedback: no


AL1838-24-K

Trend Actuator Linear 1800N 38mm

Electrical actuator for valve series: V16.. with 38 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open
Stem force: 1800N
Stroke: 38mm
Manual operation: yes
Runtime: 3,5min


Power supply: 24Vac
Control input signal: 3-pt
Position feedback: no


AL1838-P-K

Trend Actuator Linear 1800N 38mm

Electrical actuator for valve series: V16.. with 38 mm stroke.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
For floating control model:
stem position at control signal loss is selectable: closed, half open or open
Stem force: 1800N
Stroke: 38mm
Manual operation: yes
Runtime: 3,5min


Power supply: 24Vac
Control input signal: 0/2..10V=
Position feedback: 2..10V=


AQ/D

Trend Air quality sensor

For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: AQ/D IP67 Housing
Output signal: 0..10Vdc
Pre-calibrated for ease of commissioning
On site calibration if required with status LED
Long term reliability
Power supply: 24Vacdc


Mounting place: air duct
Housing (HxWxD): no
Housing (dia x D): 85mm|55mm
Immersion depth: 200mm


AQ/S

Trend Air quality sensor

For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: AQ/D IP67 Housing
Output signal: 0..10Vdc
Pre-calibrated for ease of commissioning
On site calibration if required with status LED
Long term reliability
Power supply: 24Vacdc


Mounting place: internal wall
Housing (HxWxD): 86mm|86mm|35mm
Housing (dia x D): no
Immersion depth: no


AT0102-24-SD

Trend Actuator Thermic 90N 2.5mm

Electrical actuator, on/off and PWM control, for valve series VS58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Power supply: 24Vac
Control input signal: 2-pt
Stroke: 2,5mm
Runtime: 6,0min
Initial current: 0,2A


Power loss action: stem extends


AT0102-24-SU

Trend Actuator Thermic 90N 2.5mm

Electrical actuator, on/off and PWM control, for valve series VS58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Power supply: 24Vac
Control input signal: 2-pt
Stroke: 2,5mm
Runtime: 6,0min
Initial current: 0,2A


Power loss action: stem retracts


AT0106-230-SD

Trend Actuator Thermic 90N 6.5mm

Electrical actuator, on/off and PWM control, for valve series V58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Control input signal: 2-pt
Stroke: 6,5mm


Power supply: 230Vac
Runtime: 5,5min
Initial current: 0,4A
Power loss action: stem extends


AT0106-230-SU

Trend Actuator Thermic 90N 6.5mm

Electrical actuator, on/off and PWM control, for valve series V58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Control input signal: 2-pt
Stroke: 6,5mm


Power supply: 230Vac
Runtime: 5,5min
Initial current: 0,4A
Power loss action: stem retracts


AT0106-24-SD

Trend Actuator Thermic 90N 6.5mm

Electrical actuator, on/off and PWM control, for valve series V58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Control input signal: 2-pt
Stroke: 6,5mm


Power supply: 24Vac
Runtime: 7,5min
Initial current: 0,2A
Power loss action: stem extends


AT0106-24-SU

Trend Actuator Thermic 90N 6.5mm

Electrical actuator, on/off and PWM control, for valve series V58..
Protection class: IP44
Position indication: with red indicator
Stem force: 90N
Cable length: 2,5m
Actuator supplied with mounting clip.
Control input signal: 2-pt
Stroke: 6,5mm


Power supply: 24Vac
Runtime: 7,5min
Initial current: 0,2A
Power loss action: stem retracts


AV/D/10

Trend Air Velocity sensor, Duct

Media: Air, 0 to 10m/s (default); selectable by link for 0 to 15m/s or 0 to 20m/s
Response time: 0.7s or 4s selectable by link
Mounting place: air duct
Protection class: IP 65 Housing
Output signal: 2..10Vdc + 4..20mA


BLUETOOTH ADAPT SPVR PRT

Trend Bluetooth Adaptor

The Trend Bluetooth Supervisor Port Adaptor enables SET or 916 to interrogate and configure the Trend Building Management System using wireless communication. It is designed to provide a temporary connection for commissioning purposes.The Bluetooth adaptor plugs into an IQs local supervisor port, or a CNC2s RS232 port, and will communicate with any Bluetooth enabled laptop or handheld computer. Additional adaptor cables are available for use with older IQs or CNC2s.
Simple wireless connectivity
Walk around commissioning
Enables PCs with only a USB port to be used for commissioning (via USB/Bluetooth adaptor)
No separate power supply required (powered from IQ with correct adaptor cable)


Model: Trend Bluetooth Adaptor


CABLE/58-0750

Trend Leads


Product description: Supervisor 9 Female to 25 Male cable


CABLE/58-0836

Trend Leads


Product description: Supervisor/HDP/FPK cable (3m length)


CABLE/58-0935

Trend Leads


Product description: Supervisor/HDP/FPK cable (1m length)


CABLE/78-1172

Trend Leads


Product description: Short adapter lead for local port access (5-25pin) Pre IQ2xx


CABLE/EJ100057A

Trend Leads


Product description: IQ1xx Supervisor lead, 5 way SIL F to 9 way D F (2m length)


CABLE/EJ100179A001

Trend Leads


Product description: NEIB RS232 Cable assembly (230mm length)


CABLE/EJ101442

Trend Leads


Product description: Adapter lead from supervisor to IQ25x (9 way female to RJ11)


CABLE/EJ104029

Trend Leads


Product description: IQ22x to NDP Comms lead (3m length)


CABLE/EJ104352

Trend Leads


Product description: ENC2 serial lead (150mm length)


CABLE/EJ105650

Trend Leads


Product description: RJ11 plug to RJ11 plug with crossover to connect to IQ3, IQ2xx, and some IQ1xx controllers local supervisor ports


CABLE/IQ246KIT

Trend IQ246 Controllers
Accessories

IQ246 cable set (4 cables) - 1 end unterminated



CNC2

Trend Network Cards Trend LAN

The Communications Node Controller (CNC2) interfaces between a Trend Supervisor or Software Tool and the Trend network (RS232 to Lan).
The Internetwork Node Controller (INC2) allows Lans to be interconnected to create very large networks. Up to 116 INC2s can be connected to the internetwork. An INC2 may have up to 116 devices on its Lan.
The LNC2 Lancard Node Controller is a PCI bus card that interfaces between a Trend Supervisor or Software Tool and the Trend network.
Trend Node cards (CNC/INC) available in an IP30 enclosure (NBOX) or can be supplied without an enclosure for mounting inside a Trend device, e.g. an IQ controller. There are 230 V and 24 V supply versions. Boxed battery backed versions are available (230 Vac only) and an optional metal enclosure with cable glanding knockouts is also available.
Network: Trend LAN

CNC Cards
Model: Communications Node Controller
Power: 24Vdc
Comments: no


CO2/T/D

Trend CO2/T/ Temperature, Humidity Sensors

A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)


Mounting place: air duct
Display: no
Housing (HxWxD): 105mm|97mm|57mm
Immersion depth: no


CO2/T/Disp/S

Trend CO2/T/ Temperature, Humidity Sensors

A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)


Mounting place: internal wall
Display: 4 Digit LCD
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm


CO2/T/H/Disp/S

Trend CO2/T/ Temperature, Humidity Sensors

A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)


Mounting place: internal wall
Display: 4 Digit LCD
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm


CO2/T/H/S

Trend CO2/T/ Temperature, Humidity Sensors

A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)


Mounting place: internal wall
Display: no
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm


CO2/T/S

Trend CO2/T/ Temperature, Humidity Sensors

A range of CO2 sensors designed to monitor the carbon dioxide concentration and temperature of the air. The sensors use non-dispersive infra red (NDIR) technology with an auto calibration feature to prevent measurement drift and to remove the need for re calibration. The range consists of one duct sensor and four space sensors. The space sensors are available with the options of humidity sensor and/or a 4 digit display. The display continually scrolls through the measured values and can show temperature, relative humidity and CO2.
Other features include:
Non-dispersive infra-red (NDIR) technology
Digital electronics with auto calibration feature
Integral display with continous scroll to visualise measured values.
Two part terminals to facilitate wiring
Output signal: 0 to 10 V(Space), Thermistor (Duct)


Mounting place: internal wall
Display: no
Housing (HxWxD): 86mm|86mm|26mm
Immersion depth: 260mm


CSENSOR/100

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CSENSOR
Input signal: 0 .. 100 A
Output signal: 0 .. 0.333 Vac


CSENSOR/150

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CSENSOR
Input signal: 0 .. 150 A
Output signal: 0 .. 0.333 Vac


CSENSOR/400

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CSENSOR
Input signal: 0 .. 400 A
Output signal: 0 .. 0.333 Vac


CSENSOR/50

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CSENSOR
Input signal: 0 .. 50 A
Output signal: 0 .. 0.333 Vac


CSENSOR/800

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CSENSOR
Input signal: 0 .. 800 A
Output signal: 0 .. 0.333 Vac


CT/1000S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 1000 A
Output signal: 0 .. 5 A


CT/1500S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 1500 A
Output signal: 0 .. 5 A


CT/150S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 150 A
Output signal: 0 .. 5 A


CT/1600S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 1600 A
Output signal: 0 .. 5 A


CT/2000S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 2000 A
Output signal: 0 .. 5 A


CT/200S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 200 A
Output signal: 0 .. 5 A


CT/250S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 250 A
Output signal: 0 .. 5 A


CT/400S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 400 A
Output signal: 0 .. 5 A


CT/500S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 500 A
Output signal: 0 .. 5 A


CT/800S

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CT
Input signal: 0 .. 800 A
Output signal: 0 .. 5 A


CTX/200

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CTX
Input signal: 0 .. 200 A
Output signal: 0..10Vdc


CTX/500

Trend Current Transformers

A range of current tranformers and transducers for use with the electricity meters. Each is tailored to a particlar application as explained in the descriptions below.
The CTX range of fully insulated split ring current transducers provide direct measurement of current flow and are intended for use in a wide range of applications or for low cost monitoring. Installation of the lightweight air core CTX is very easy. The unit is simply clipped around the conductor and secured with a cable tie.
The CT system range of split core current transformers are designed for use in conjunction with the IQ system EM Series Electricity Meters (not EM/RX) or any other suitable meter. They are tape wrapped and are complete with 1 metre length flying leads. These transformers are available in a number of ratings to cater for all types of installation.
The CSENSOR series of retrofit (split-core) current sensors are designed for fast and easy installation without the need to disconnect any loads. H igh precision units, they a re equally suitable for Current or Power measurement - only for use with the EM-MPO/350e and the EM-MPO/400e multi-parameter electricity meters. An internal precision resistor across the secondary winding of the sensor provides a safe low voltage output - no more worries about open-circuiting CT secondary circuits.
Accuracy: Class 1

CTX
Input signal: 0 .. 500 A
Output signal: 0..10Vdc


DPCM/24VAC

Trend Input and Output Modules

Trend I/O Modules convert either digital input signals into an analogue signal to be read by the controller, or an analogue signal from the controller to a number of stages of relay output. They act as an interface between the controller and heating and ventilating equipment.
The Digital Input Expander allows 4 volt free inputs to be monitored by a single analogue input channel. The resultant analogue value can be decoded by the A to D Function Module in an IQ controller to produce internal digital status bits for alarm monitoring or other status input applications.
The Single Relay Module (SRM) enables a controller output signal to drive a single changeover relay. The 2SRM houses two single relays.
The Two Relay Module (2RM) may be configured as a high/low or a raise/lower relay module by link selection.
The Three Relay Module (3RM) may be configured as a Fan/Heating/Cooling sequence controller (HCM) or a 3 stage sequence controller (TRM) using the operating mode link.
The Six Relay Module (6RM) converts an analogue output of an IQ controller to six stages of relay output.
The Voltage to Current Driver is a two channel output interface which converts two 0 to 10V signals into two 0 to 20 mA outputs.
The Dual Phase Cut Module converts two controller analogue output signals to two 20 V phase cut signals for controlling valves and actuators in heating and ventilating equipment. Opto-isolation is used to isolate the control signals from the outputs to ensure that no ground conflicts can occur.
Standard DIN rail mounting.
Rising cage clamp terminals.
24 Vac/dc supply.

Output Modules
Product description: Dual Phase Cut Module; 15 VA max per channel.


DPIA-100-250

Trend Differential Pressure, Current sensor, Air

For filter, valve, damper, fan, blower, flap and air flow monitoring and control, and environmental protection.
Kind of pressure: differential pressure, relative
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: -10...70C
Two pressure ranges selectable. All DPIA differential pressure transmitters are factory pre-set to pressure range 1.
Output signal: 4..20mA


Pressure range: 0...100/250Pa
Max. pressure: 20kPa


DPIA-1000-2500

Trend Differential Pressure, Current sensor, Air

For filter, valve, damper, fan, blower, flap and air flow monitoring and control, and environmental protection.
Kind of pressure: differential pressure, relative
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: -10...70C
Two pressure ranges selectable. All DPIA differential pressure transmitters are factory pre-set to pressure range 1.
Output signal: 4..20mA


Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa


DPIA-250-500

Trend Differential Pressure, Current sensor, Air

For filter, valve, damper, fan, blower, flap and air flow monitoring and control, and environmental protection.
Kind of pressure: differential pressure, relative
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: -10...70C
Two pressure ranges selectable. All DPIA differential pressure transmitters are factory pre-set to pressure range 1.
Output signal: 4..20mA


Pressure range: 0...250/500Pa
Max. pressure: 20kPa


DPIA-500-1000

Trend Differential Pressure, Current sensor, Air

For filter, valve, damper, fan, blower, flap and air flow monitoring and control, and environmental protection.
Kind of pressure: differential pressure, relative
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: -10...70C
Two pressure ranges selectable. All DPIA differential pressure transmitters are factory pre-set to pressure range 1.
Output signal: 4..20mA


Pressure range: 0...500/1000Pa
Max. pressure: 20kPa


DPIL/0.5

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...0,5bar
Max. pressure: 3bar


DPIL/1

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...1bar
Max. pressure: 5bar


DPIL/10

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...10bar
Max. pressure: 20/12.bar


DPIL/2.5

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...2,5bar
Max. pressure: 12bar


DPIL/4

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...4bar
Max. pressure: 12bar


DPIL/6

Trend Differential Pressure, Current sensor, Liquid

The DPIL is suitable for measurement of differential pressures across pumps, boilers, chillers, filters etc. in HVAC applications.
Kind of pressure: differential
Pressure connection: screw compression fittings for 6 mm pipe.
Electrical connection: DIN(4350-A)
Protection class: IP65
Housing material: housing in contact with medium: Ceramic/INOX 1.4305, PTFE
Sensing method: piezoresistive
Media temp.: -15...80C
Medium: liquid
Ambient temperature: -15...80C
Output signal: 4..20mA


Pressure range: 0...6bar
Max. pressure: 12bar


DPSA-1000

Trend Differential Pressure, Switch, Air

For monitoring filter, fan, fire damper, or air flow status of air handling systems.
Kind of pressure: differential
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Housing material: ABS and POM
Media temp.: -20...85C
Medium: gaseous
Ambient temperature: -20...85C
Max. pressure: 5kPa


Pressure range: 200...1000Pa


DPSA-200

Trend Differential Pressure, Switch, Air

For monitoring filter, fan, fire damper, or air flow status of air handling systems.
Kind of pressure: differential
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Housing material: ABS and POM
Media temp.: -20...85C
Medium: gaseous
Ambient temperature: -20...85C
Max. pressure: 5kPa


Pressure range: 20...200Pa


DPSA-400

Trend Differential Pressure, Switch, Air

For monitoring filter, fan, fire damper, or air flow status of air handling systems.
Kind of pressure: differential
Pressure connection: Supplied complete with connection kit comprising 2m of 6mm tubing, 2 connection tubes, and 4 screws
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Housing material: ABS and POM
Media temp.: -20...85C
Medium: gaseous
Ambient temperature: -20...85C
Max. pressure: 5kPa


Pressure range: 40...400Pa


DPSL/H

Trend Differential Pressure, Switch, Liquid

Differential pressure, vacuum and overpressure switch for monitoring neutral and slightly aggressive liquids and gases. It can be used as a flow switch fitted across an orifice plate.
Kind of pressure: differential pressure, relative
Pressure connection: G1/8" (DIN 259); 1/8" BSP female thread
Electrical connection: screw terminals
Protection class: IP54
Housing material: Case: Brass, Cover: Plastic, Diaphragm: EPDM
Media temp.: -10...80C
Medium: liquid/gaseous
Ambient temperature: -10...80C
Max. pressure: 10bar


Pressure range: 150...1000mbar


DPSL/L

Trend Differential Pressure, Switch, Liquid

Differential pressure, vacuum and overpressure switch for monitoring neutral and slightly aggressive liquids and gases. It can be used as a flow switch fitted across an orifice plate.
Kind of pressure: differential pressure, relative
Pressure connection: G1/8" (DIN 259); 1/8" BSP female thread
Electrical connection: screw terminals
Protection class: IP54
Housing material: Case: Brass, Cover: Plastic, Diaphragm: EPDM
Media temp.: -10...80C
Medium: liquid/gaseous
Ambient temperature: -10...80C
Max. pressure: 10bar


Pressure range: 40...200mbar


EAO

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

I/O Cards
AI: no
DI: no
AO: 8
DO: no
Comments: no
Power: no


EDO

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

I/O Cards
AI: no
DI: no
AO: no
DO: 8
Comments: no
Power: no


EDS-205

Trend Network Cards Ethernet

The 3xtend/EINC L enables IQ networks running on the IQ System current loop Lan, Ethernet, and LON to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EINC, Ethernet Internetwork Node Controller, provides the means by which the Building Management System network can incorporate an Ethernet network. The EINC operates at the internetwork level, including the necessary support for WANs (e.g. TMN support). It also provides virtual CNCs which allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EDS-205 and EDS-305-M-SC are industrial 5-port Ethernet switch that supports IEE 820.3/820.3u/820.3x with 10/100M, full half duplex, MDI/MDIX autosensing RJ45 ports. The EDS-305-M-SC also has a built in relay warning function which alerts maintainers when power failures or port breaks occur and is equipped with 4 10/100T(X) ports and 1 single mode 100baseFX port, SC connector. Both devices operate over a wide temperature range and are DIN rail mounting, making them ideal for most industrial environments.
The IMC-101-M-SC,which has been designed for stable operation in industrial environments, provides conversion between 10/100BaseT(X) and 100 BaseFX. It rated to operate at temperature ranging from 0 - 60oC, and is DIN rail mounting, making it ideal for most industrial environments.

Switches
Model: Ethernet Switch
Network: TCP/IP
Power: 24Vac/dc
Comments: IP30


EDS-305-M-SC

Trend Network Cards Ethernet

The 3xtend/EINC L enables IQ networks running on the IQ System current loop Lan, Ethernet, and LON to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EINC, Ethernet Internetwork Node Controller, provides the means by which the Building Management System network can incorporate an Ethernet network. The EINC operates at the internetwork level, including the necessary support for WANs (e.g. TMN support). It also provides virtual CNCs which allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EDS-205 and EDS-305-M-SC are industrial 5-port Ethernet switch that supports IEE 820.3/820.3u/820.3x with 10/100M, full half duplex, MDI/MDIX autosensing RJ45 ports. The EDS-305-M-SC also has a built in relay warning function which alerts maintainers when power failures or port breaks occur and is equipped with 4 10/100T(X) ports and 1 single mode 100baseFX port, SC connector. Both devices operate over a wide temperature range and are DIN rail mounting, making them ideal for most industrial environments.
The IMC-101-M-SC,which has been designed for stable operation in industrial environments, provides conversion between 10/100BaseT(X) and 100 BaseFX. It rated to operate at temperature ranging from 0 - 60oC, and is DIN rail mounting, making it ideal for most industrial environments.

Switches
Model: Ethernet Switch
Network: TCP/IP
Power: 24Vac/dc
Comments: IP30


EIN

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

I/O Cards
AI: 8
DI: 8
AO: no
DO: no
Comments: no
Power: no


EM-MPO/350

Trend Electricity Meter, Three Phase, Multi Parameter

The EM-MPO/350 is a DIN rail mounted 3 phase multiparameter electricity meter with an (8 digit) LCD display and The EM-MPO/400 is a panel mounting 3 phase multi-parameter electricity meter with a backlit 3 line display. The /350 and the /400 require 5 A current transformers, whereas the /350e and /400e use the CSENSOR range of split core current sensors. Voltage transformers may be used for medium to extra high voltage. The required transformer ratio is programmable from the panel. Used in conjunction with the EMIC (Ethernet Metering Interface Controller) or a Trend IQ3/XNC MODBUS driver, logged data can be accessed directly over the Trend network.
Multi-parameter metering
Backlit LCD display
/350 and /400 use CTs (CT/.. split core range available)
/350e and /400e use current sensors (CSENSOR/.. split core sensor range available)
RS485 MODBUS interface
Interfaces to Trend system (using MODBUS driver or EMIC)
Isolated pulse output available
True RMS measurement to the 30th harmonic
RS485 port: RS485 MODBUS, 2 wire + 0 V half duplex, quarter unit load. Baud rate programmable 4k8, 9k6 19k2 baud.
Input voltage: 3x230/400Vac
Accuracy: Class 1


Current: 5A
Wiring connection: via CT
Mounting: DIN rail


EM-MPO/350e

Trend Electricity Meter, Three Phase, Multi Parameter

The EM-MPO/350 is a DIN rail mounted 3 phase multiparameter electricity meter with an (8 digit) LCD display and The EM-MPO/400 is a panel mounting 3 phase multi-parameter electricity meter with a backlit 3 line display. The /350 and the /400 require 5 A current transformers, whereas the /350e and /400e use the CSENSOR range of split core current sensors. Voltage transformers may be used for medium to extra high voltage. The required transformer ratio is programmable from the panel. Used in conjunction with the EMIC (Ethernet Metering Interface Controller) or a Trend IQ3/XNC MODBUS driver, logged data can be accessed directly over the Trend network.
Multi-parameter metering
Backlit LCD display
/350 and /400 use CTs (CT/.. split core range available)
/350e and /400e use current sensors (CSENSOR/.. split core sensor range available)
RS485 MODBUS interface
Interfaces to Trend system (using MODBUS driver or EMIC)
Isolated pulse output available
True RMS measurement to the 30th harmonic
RS485 port: RS485 MODBUS, 2 wire + 0 V half duplex, quarter unit load. Baud rate programmable 4k8, 9k6 19k2 baud.
Input voltage: 3x230/400Vac
Accuracy: Class 1


Current: no
Wiring connection: no
Mounting: DIN rail


EM-MPO/400

Trend Electricity Meter, Three Phase, Multi Parameter

The EM-MPO/350 is a DIN rail mounted 3 phase multiparameter electricity meter with an (8 digit) LCD display and The EM-MPO/400 is a panel mounting 3 phase multi-parameter electricity meter with a backlit 3 line display. The /350 and the /400 require 5 A current transformers, whereas the /350e and /400e use the CSENSOR range of split core current sensors. Voltage transformers may be used for medium to extra high voltage. The required transformer ratio is programmable from the panel. Used in conjunction with the EMIC (Ethernet Metering Interface Controller) or a Trend IQ3/XNC MODBUS driver, logged data can be accessed directly over the Trend network.
Multi-parameter metering
Backlit LCD display
/350 and /400 use CTs (CT/.. split core range available)
/350e and /400e use current sensors (CSENSOR/.. split core sensor range available)
RS485 MODBUS interface
Interfaces to Trend system (using MODBUS driver or EMIC)
Isolated pulse output available
True RMS measurement to the 30th harmonic
RS485 port: RS485 MODBUS, 2 wire + 0 V half duplex, quarter unit load. Baud rate programmable 4k8, 9k6 19k2 baud.
Input voltage: 3x230/400Vac
Accuracy: Class 1


Current: 5A
Wiring connection: via CT
Mounting: Panel Mounting


EM-MPO/400e

Trend Electricity Meter, Three Phase, Multi Parameter

The EM-MPO/350 is a DIN rail mounted 3 phase multiparameter electricity meter with an (8 digit) LCD display and The EM-MPO/400 is a panel mounting 3 phase multi-parameter electricity meter with a backlit 3 line display. The /350 and the /400 require 5 A current transformers, whereas the /350e and /400e use the CSENSOR range of split core current sensors. Voltage transformers may be used for medium to extra high voltage. The required transformer ratio is programmable from the panel. Used in conjunction with the EMIC (Ethernet Metering Interface Controller) or a Trend IQ3/XNC MODBUS driver, logged data can be accessed directly over the Trend network.
Multi-parameter metering
Backlit LCD display
/350 and /400 use CTs (CT/.. split core range available)
/350e and /400e use current sensors (CSENSOR/.. split core sensor range available)
RS485 MODBUS interface
Interfaces to Trend system (using MODBUS driver or EMIC)
Isolated pulse output available
True RMS measurement to the 30th harmonic
RS485 port: RS485 MODBUS, 2 wire + 0 V half duplex, quarter unit load. Baud rate programmable 4k8, 9k6 19k2 baud.
Input voltage: 3x230/400Vac
Accuracy: Class 1


Current: no
Wiring connection: no
Mounting: Panel Mounting


EM3/CT/N

Trend Electricity Meter, ThreePhase Pulse

Three phase electronic KWh meters, with DIN rail mounting, volt free pulsed outputs.
Output signal: volt free pulsed


Input voltage: 230/400Vac 3 phase, 3 or 4 wire
Current: 5A
Wiring connection: via CT
Accuracy: Class 1 - EN 61036


EM3/CT/ODIN

Trend Electricity Meter, ThreePhase Pulse

Three phase electronic KWh meters, with DIN rail mounting, volt free pulsed outputs.
Output signal: volt free pulsed


Input voltage: 3x230/400Vac
Current: 10A
Wiring connection: via CT
Accuracy: Class 2 - IEC 61036


EM3/D/ODIN

Trend Electricity Meter, ThreePhase Pulse

Three phase electronic KWh meters, with DIN rail mounting, volt free pulsed outputs.
Output signal: volt free pulsed


Input voltage: 3x230/400Vac
Current: 65A
Wiring connection: direct
Accuracy: Class 2 - IEC 61036


EMIC/MBA/10

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

MBus
Interface: M-Bus
Comments: For 10 devices


EMIC/MBA/20

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

MBus
Interface: M-Bus
Comments: For 20 devices


EMIC/MBA/3

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

MBus
Interface: M-Bus
Comments: For 3 devices


EMIC/MDA/16

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

ModBus
Interface: ModBus
Comments: For 16 devices


EMIC/MDA/32

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

ModBus
Interface: ModBus
Comments: For 32 devices


EMIC/MDA/8

Trend Ethernet Metering Interface Controller

The EMIC (Ethernet Metering Interface Controller) provides an interface for up to 8, 16 or 32 energy meters. It connects to the Trend system using Ethernet, and to the meters using RS485, MODBUS. It sits on the Trend internetwork, and takes a Lan for its own use, each meter being represented by an outstation on that Lan. Data from each meter is collected using the RS485 bus and stored in the EMIC within the relevant outstation. Each meter can be chosen from a range of meters from various suppliers including the Trend EM-MPO/SIRIO and /STAR3. It can be configured using an integral web server
Versions for 8, 16, or 32 MODBUS meters
A wide range of easily selectable meter definitions is available
Configurable using built-in web pages
Meters appear as outstations on a Lan
RS485 cable provided
EMIC IPTool can find EMICs IP addresses
Can calculate cumulative kWh over defined period
Network: TCP/IP

ModBus
Interface: ModBus
Comments: For 8 devices


ENCLS-600002

Trend IQeco31 controller
Accessories

IQECO/IQL secondary terminal cover.



ENCLS/

Trend IQ251 Controllers
Accessories

600x600mm enclosure (accepts all IQ200 series controllers except IQ246)



ENCLS/MBOX/IQ21X

Trend IQ21x Controllers
Accessories

Steel enclosure for Trend IQ21x products



ENCLS/MBOX/IQ22X

Trend IQ22x Controllers
Accessories

Steel Enclosure for Trend IQ22x and NBOX products



GVCPI-100

Trend Solenoid gas valve flanged, normally closed
CPI switches

CPI switch for the GVF100-230



GVCPI-20-25

Trend Solenoid gas valve screwed, normally closed
CPI switches

CPI switch for the GVS20-230 & GVS25-230



GVCPI-32-40

Trend Solenoid gas valve screwed, normally closed
CPI switches

CPI switch for the GVS32-230 & GVS40-230



GVCPI-50

Trend Solenoid gas valve screwed, normally closed
CPI switches

CPI switch for the GVS50-230



GVCPI-65F-80

Trend Solenoid gas valve screwed, normally closed
CPI switches

CPI switch for the GVS80-230



GVCPI-65S

Trend Solenoid gas valve screwed, normally closed
CPI switches

CPI switch for the GVS65-230



GVF100-230

Trend Solenoid gas valve flanged, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection type: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Flanged 220...240 Vac versions
Valve size: 4inch
Optional CPI-switch: GVCPI-100


GVF65-230

Trend Solenoid gas valve flanged, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection type: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Flanged 220...240 Vac versions
Valve size: 2 1/2inch
Optional CPI-switch: GVCPI-65F-80


GVF80-230

Trend Solenoid gas valve flanged, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air.
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVF65-230 and GVF80-230 have adjustable maximum flow rate on the bottom of the coil
4 auxiliary pressure taps with Rp 1/4" threaded connections, 2 on the inlet side, 2 on the outlet side.
Max. operating pressure: 200mbar
Port connection type: flanges ISO7005
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Flanged 220...240 Vac versions
Valve size: 3inch
Optional CPI-switch: GVCPI-65F-80


GVS20-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 3/4inch
Optional CPI-switch: GVCPI-20-25


GVS25-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 1inch
Optional CPI-switch: GVCPI-20-25


GVS32-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 1 1/4inch
Optional CPI-switch: GVCPI-32-40


GVS40-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 1 1/2inch
Optional CPI-switch: GVCPI-32-40


GVS50-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 2inch
Optional CPI-switch: GVCPI-50


GVS65-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 2 1/2inch
Optional CPI-switch: GVCPI-65S


GVS80-230

Trend Solenoid gas valve screwed, normally closed

Class "A" Safety Shutoff Solenoid Gas Valve with threaded connections.
For control and regulation of gaseous fluids in gas power burners, gas boilers, ovens, furnaces and other gas consuming appliances.
Gas valve type: non regulated ON/OFF normally closed, fast opening
Media: natural gas, propane, air
Materials: aluminium die cast body
Protection class: IP54
Electrical connection: PG11
Approvals: class "A" in accordance with EN161
Optional Closed Position Indication Switch (CPI switch) is ordered separately
GVS80-230 has adjustable maximum flow rate on top of the coil
Max. operating pressure: 200mbar
Port connection type: internal threads
Threads type: BSP
Ambient temperature: -15...60C
Maximum opening time: 1s
Maximum closing time: 1s

Threaded 220...240 Vac versions
Valve size: 3inch
Optional CPI-switch: GVCPI-65F-80


HMAC /TAIL

Trend TREND HEAT METER
Accessories

R 1/2 external thread (M10x1 sensor thread) adapter for connection of temperature sensor



HMAC /VAL VE/25

Trend TREND HEAT METER
Accessories

G 1 internal thread ball valve with connection for temperature sensor



HMAC /VALVE/15

Trend TREND HEAT METER
Accessories

G 1/2 internal thread ball valve with connection for temperature sensor



HMAC /VALVE/20

Trend TREND HEAT METER
Accessories

G 3/4 internal thread ball valve with connection for temperature sensor



HMM/H/0.6/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating only)
Nominal flow (qp): 0,6m3/h
DN size: 15mm
Length: 110mm
Port diameter: G 3/4 Binch


HMM/H/1.5/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating only)
Nominal flow (qp): 1,5m3/h
DN size: 15mm
Length: 110mm
Port diameter: G 3/4 Binch


HMM/H/2.5/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating only)
Nominal flow (qp): 2,5m3/h
DN size: 20mm
Length: 130mm
Port diameter: G 1 Binch


HMM/HC/0.6/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 0,6m3/h
DN size: 15mm
Length: 110mm
Port diameter: G 3/4 Binch


HMM/HC/1.5/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 1,5m3/h
DN size: 15mm
Length: 110mm
Port diameter: G 3/4 Binch


HMM/HC/10/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 10m3/h
DN size: 40mm
Length: 300mm
Port diameter: G 2 Binch


HMM/HC/2.5/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 2,5m3/h
DN size: 20mm
Length: 130mm
Port diameter: G 1 Binch


HMM/HC/3.5/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 3,5m3/h
DN size: 25mm
Length: 260mm
Port diameter: G 1 1/4 Binch


HMM/HC/6.0/MOD

Trend TREND HEAT METER

The Trend HMM Series Mechanical Heat Meters are static compact energy meters with electronic measurement. Each meter consists of an electronic energy integrator with temperature sensors and a mechanical volume measuring component. HMM meters provide metering of heating and/or cooling energy in hydronic systems based on volume, and supply and return temperatures. HMM/H models are for energy metering of heating systems, ../HC models are for cooling or heat/cool systems. Used in conjunction with an RS232 and Mbus convertor and a Trend IQ3/XNC M-Bus driver, the meters data can be accessed over the Trend network.
The features include:
Electronic sensor control for recording flow rate
Available in nominal flow rates from 0.6 to 10 m3/h
DN15 and DN20 meter versions with direct electronic impeller scanning
DN25 and DN40 meter versions with magnetic coupling for electronic scanning of sensor disc
10 year battery life
Primary interface: M-Bus interface to EN1434-3
Optical ZVEI interface to IEC 870-5
Adjustable reading date for billing
Windows-based HYDRO-SET software for optimum adaption to user-specific requirements
Power source: 3V(lithium battery)
Display: LCD, 7-digit, (MWh, kWh, GJ, MJ, kW, m3/h, l/h, m3, l)
Product Type: Compact heat meter to EN 1434
Max. operating pressure: 16bar
Interface: M-Bus

Mechanical Heat Meters (heating and cooling)
Nominal flow (qp): 6m3/h
DN size: 25mm
Length: 260mm
Port diameter: G 1 1/4 Binch


HS90

Trend Dewpoint Hygrostat

The HS90 dewpoint hygrostat measures the relative humidity near the dewpoint using its high-quality capacitive sensor. The relay output will switch as the RH reaches 90%. It can be used in chilled ceiling, heating, ventilating, and air conditioning applications.
An additional status light indicates the condensation danger. Thanks to the special protection coating, the sensor and its electronics exhibit low susceptibility to dust and dirt. The HS90 can be mounted on walls, ducts and pipes up to 2" (50 mm).
R.H. range: 0...100%rh
Mounting place: strap on pipe
early detection of condensation danger
compact design
fast response time
dust protection
simple and easy mounting
status indication
Output signal: volt free contact
R.H. hysteresis switching point: 90 +/-5%rh


HT/D

Trend Plant Humidity Sensors

Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)


R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no
Mounting place: air duct


HT/D/2%

Trend Plant Humidity Sensors

Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)


R.H. calibration: 2%rh
Temperature element: Pt1000
Output signal: 4..20mA
Mounting place: air duct


HT/O

Trend Plant Humidity Sensors

Duct and externally mounted relative humidity and temperature sensors for HVAC applications. The certified 2% high accuracy (duct only) and standard 3% versions offer excellent linearity and stability over a wide humidity range (10 to 90 %RH).
The Externally mounted sensor is fitted with a radiation shield to avoid solar, rain and wind effects.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
R.H. output signal: 4..20mA
Temperature range: 0...40C
Precalibrated for ease of commissioning
IP65
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability
Adjustable depth duct mounting flange option (duct version)
Radiation shield reduces solar, rain, and wind effects (outside version)


R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no
Mounting place: wall outside


HT/S

Trend Space Humidity Sensors

Wall mounted relative humidity measurement combined with temperature measurement. The certified 2% high accuracy and standard 3% versions offer excellent linearity and stability over a wide humidity range.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
Temperature range: 0...40C
Mounting place: internal wall
Precalibrated for ease of commissioning
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability


R.H. calibration: 3%rh
Temperature element: NTC10k
Output signal: no


HT/S/2%

Trend Space Humidity Sensors

Wall mounted relative humidity measurement combined with temperature measurement. The certified 2% high accuracy and standard 3% versions offer excellent linearity and stability over a wide humidity range.
R.H. range: 0...100%rh
R.H. sensing element: capacitive
Temperature range: 0...40C
Mounting place: internal wall
Precalibrated for ease of commissioning
Operates over 0 to 100 %RH non-condensing
2% and 3% accuracy versions
2 part connectors for ease of installation
Humidity sensor element protected by replaceable filter
Capacitive humidity sensing element provides excellent long term stability


R.H. calibration: 2%rh
Temperature element: Pt1000
Output signal: 4..20mA


IMC-101-M-SC

Trend Network Cards Ethernet

The 3xtend/EINC L enables IQ networks running on the IQ System current loop Lan, Ethernet, and LON to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EINC, Ethernet Internetwork Node Controller, provides the means by which the Building Management System network can incorporate an Ethernet network. The EINC operates at the internetwork level, including the necessary support for WANs (e.g. TMN support). It also provides virtual CNCs which allow supervisory or tool software running in PCs connected to the Ethernet network to connect to the BMS system.
The EDS-205 and EDS-305-M-SC are industrial 5-port Ethernet switch that supports IEE 820.3/820.3u/820.3x with 10/100M, full half duplex, MDI/MDIX autosensing RJ45 ports. The EDS-305-M-SC also has a built in relay warning function which alerts maintainers when power failures or port breaks occur and is equipped with 4 10/100T(X) ports and 1 single mode 100baseFX port, SC connector. Both devices operate over a wide temperature range and are DIN rail mounting, making them ideal for most industrial environments.
The IMC-101-M-SC,which has been designed for stable operation in industrial environments, provides conversion between 10/100BaseT(X) and 100 BaseFX. It rated to operate at temperature ranging from 0 - 60oC, and is DIN rail mounting, making it ideal for most industrial environments.

Switches
Model: Ethernet Converter
Network: TCP/IP
Power: 24Vac/dc
Comments: IP30


INC2

Trend Network Cards Trend LAN

The Communications Node Controller (CNC2) interfaces between a Trend Supervisor or Software Tool and the Trend network (RS232 to Lan).
The Internetwork Node Controller (INC2) allows Lans to be interconnected to create very large networks. Up to 116 INC2s can be connected to the internetwork. An INC2 may have up to 116 devices on its Lan.
The LNC2 Lancard Node Controller is a PCI bus card that interfaces between a Trend Supervisor or Software Tool and the Trend network.
Trend Node cards (CNC/INC) available in an IP30 enclosure (NBOX) or can be supplied without an enclosure for mounting inside a Trend device, e.g. an IQ controller. There are 230 V and 24 V supply versions. Boxed battery backed versions are available (230 Vac only) and an optional metal enclosure with cable glanding knockouts is also available.
Network: Trend LAN

INC Cards
Model: Internetwork Node Controller
Power: 24Vdc
Comments: no


IQ211/UNB/230

Trend IQ21x Controllers

The IQ21x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ21x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs.
Network: Trend LAN
UI: 1
AI: 2
DI: 2
Comments: analogue input: thermistor only

Controllers
AO: no
Triac: 6
Power: 230Vac


IQ211/UNB/24VAC

Trend IQ21x Controllers

The IQ21x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ21x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs.
Network: Trend LAN
UI: 1
AI: 2
DI: 2
Comments: analogue input: thermistor only

Controllers
AO: no
Triac: 6
Power: 24Vac


IQ212/UNB/230

Trend IQ21x Controllers

The IQ21x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ21x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs.
Network: Trend LAN
UI: 1
AI: 2
DI: 2
Comments: analogue input: thermistor only

Controllers
AO: 2
Triac: 4
Power: 230Vac


IQ212/UNB/24VAC

Trend IQ21x Controllers

The IQ21x series of intelligent controllers are designed for use as unitary controllers in building control systems. Full compatibility with other Trend IQ controllers enables the IQ21x to integrate the local environmental needs with the bulk air conditioning system in order to optimise both comfort and running costs.
Network: Trend LAN
UI: 1
AI: 2
DI: 2
Comments: analogue input: thermistor only

Controllers
AO: 2
Triac: 4
Power: 24Vac


IQ221/UNB/230

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 6
DI: no
AO: 2
DO: 5
Power: 230Vac


IQ221/UNB/24V

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 6
DI: no
AO: 2
DO: 5
Power: 24Vac/dc


IQ222/UNB/230

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 6
DI: no
AO: 6
DO: no
Power: 230Vac


IQ222/UNB/24V

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 6
DI: no
AO: 6
DO: no
Power: 24Vac/dc


IQ223/UNB/230

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: 7
DO: 1
Power: 230Vac


IQ223/UNB/24V

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: 7
DO: 1
Power: 24Vac/dc


IQ228/UNB/230

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: no
DO: no
Power: 230Vac


IQ228/UNB/24V

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: no
DO: no
Power: 24Vac/dc


IQ229/UNB/230

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: 7
DO: 5
Power: 230Vac


IQ229/UNB/24V

Trend IQ22x Controllers

Medium size controller with extremely versatile I/O capability suitable for a broad range of applications, especially in the area of dedicated controls (e.g. air handling units, terminal units, chillers). Various I/O configurations available, ranging from 8 points to 20 points.
Network: Trend LAN

Controllers
UI: 7
DI: 1
AO: 7
DO: 5
Power: 24Vac/dc


IQ231/UNB/230

Trend IQ23x Controllers

The IQ231 and IQ233 mid range controllers are specifically designed for field replacement of the older IQ111 (111+) and IQ131 (131+) controllers respectively. They are also useful in new installations, for a broad range of applications. The IQ231 has 16 input/output points, and the IQ233 has 32 points. Options are available for integral node cards.
Order example: IQ231/TMNH/UK/230
Network: Trend LAN
Power: 230Vac

Controllers
UI: 8
AO: 8


IQ233/UNB/230

Trend IQ23x Controllers

The IQ231 and IQ233 mid range controllers are specifically designed for field replacement of the older IQ111 (111+) and IQ131 (131+) controllers respectively. They are also useful in new installations, for a broad range of applications. The IQ231 has 16 input/output points, and the IQ233 has 32 points. Options are available for integral node cards.
Order example: IQ231/TMNH/UK/230
Network: Trend LAN
Power: 230Vac

Controllers
UI: 20
AO: 12


IQ241/UNB/230

Trend IQ241 Controllers

The IQ241 controllers are of medium capacity designed for the control of all types of building plant. They can provide a minimum of 12 digital inputs, and 8 analogue voltage outputs. A further 20 I/O points can be made available by using up to 10 S cards, each providing 2 inputs or outputs of the same type (8 input only, 12 input or output). S cards can provide analogue current, analogue voltage, thermistor, or digital inputs, or analogue voltage outputs giving the IQ241 sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Network: Trend LAN

Controllers
AI: no
DI: 12
AO: 8
Comments: up to 10 cards
Power: 230Vac


IQ241/UNB/24VAC

Trend IQ241 Controllers

The IQ241 controllers are of medium capacity designed for the control of all types of building plant. They can provide a minimum of 12 digital inputs, and 8 analogue voltage outputs. A further 20 I/O points can be made available by using up to 10 S cards, each providing 2 inputs or outputs of the same type (8 input only, 12 input or output). S cards can provide analogue current, analogue voltage, thermistor, or digital inputs, or analogue voltage outputs giving the IQ241 sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Network: Trend LAN

Controllers
AI: no
DI: 12
AO: 8
Comments: up to 10 cards
Power: 24Vac


IQ241/UNB/24VDC

Trend IQ241 Controllers

The IQ241 controllers are of medium capacity designed for the control of all types of building plant. They can provide a minimum of 12 digital inputs, and 8 analogue voltage outputs. A further 20 I/O points can be made available by using up to 10 S cards, each providing 2 inputs or outputs of the same type (8 input only, 12 input or output). S cards can provide analogue current, analogue voltage, thermistor, or digital inputs, or analogue voltage outputs giving the IQ241 sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Network: Trend LAN

Controllers
AI: no
DI: 12
AO: 8
Comments: up to 10 cards
Power: 24Vdc


IQ246/UNB/24VAC

Trend IQ246 Controllers

The IQ246 is designed to provide a small footprint with a relatively high capacity of inputs and outputs and can be used for the control of all types of building plant. Pre-fitting the controller bracket enable the plant and supplies to be wired in advance, and the controller to be plugged in for commissioning. D-type connectors are provided for the inputs and outputs enabling multi-core cabling to bespoke terminal layouts. The IQ246 can provide up to 32 digital inputs, 20 analogue inputs and 20 voltage outputs. All analogue inputs can be individually link-configured for voltage current or thermistor signals. It can operate either as a stand-alone device or as a part of a Building Management System.
Network: Trend LAN
AI: 20
DI: 32
AO: 20

Controllers
Power: 24Vac


IQ246/UNB/24VDC

Trend IQ246 Controllers

The IQ246 is designed to provide a small footprint with a relatively high capacity of inputs and outputs and can be used for the control of all types of building plant. Pre-fitting the controller bracket enable the plant and supplies to be wired in advance, and the controller to be plugged in for commissioning. D-type connectors are provided for the inputs and outputs enabling multi-core cabling to bespoke terminal layouts. The IQ246 can provide up to 32 digital inputs, 20 analogue inputs and 20 voltage outputs. All analogue inputs can be individually link-configured for voltage current or thermistor signals. It can operate either as a stand-alone device or as a part of a Building Management System.
Network: Trend LAN
AI: 20
DI: 32
AO: 20

Controllers
Power: 24Vdc


IQ251/UNB/230

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

Controllers
AI: no
DI: no
AO: no
DO: no
Comments: up to 8 cards
Power: 230Vac


IQ251/UNB/24VAC

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

Controllers
AI: no
DI: no
AO: no
DO: no
Comments: up to 8 cards
Power: 24Vac


IQ251/UNB/24VDC

Trend IQ251 Controllers

The IQ251 is a large capacity controller designed for the control of all types of building plant. It can provide up to 128 I/O points by connecting 8 I/O modules in any combination. IQ system accessory modules may be connected to the input/output channels to provide greater I/O flexibility. They enable the IQ251 to provide sufficient capability for more complex strategies. It can operate either as a stand alone device or as part of a Building Management System.
Order example: IQ251/comms/voltage e.g. IQ251/TMNH/UK/230. I/O cards must be ordered separately
Network: Trend LAN

Controllers
AI: no
DI: no
AO: no
DO: no
Comments: up to 8 cards
Power: 24Vdc


IQ3/XNC-DRIVERS

Trend IQ3 Integration Controllers
Accessories

Drivers for M-Bus and ModBus (free download from www.trendcontrols.com)



IQ3XACT/12/100-240

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XACT/12/24

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XACT/12/BAC/100-240

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XACT/12/BAC/24

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XACT/12/LAN/100-240

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XACT/12/LAN/24

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XACT/12/LAN/BAC/100-240

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XACT/12/LAN/BAC/24

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/LAN/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/LAN/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/LAN/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/LAN/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/SER/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/SER/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/12/XNC/SER/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XACT/12/XNC/SER/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: 6
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XACT/XML/UP

Trend IQ3 Web Enabled Controllers
Accessories

Upgrade to add XML services to IQ3xact v2.2 or greater



IQ3XCITE/00/XNC/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/00/XNC/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/00/XNC/LAN/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/LAN/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/00/XNC/LAN/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/LAN/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/00/XNC/SER/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/SER/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/00/XNC/SER/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 100..240Vac


IQ3XCITE/00/XNC/SER/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: no expansion
Power: 24Vac/24..60Vdc


IQ3XCITE/128/100-240

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/128/24

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/128/BAC/100-240

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/128/BAC/24

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/128/LAN/100-240

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/128/LAN/24

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/128/LAN/BAC/100-240

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/128/LAN/BAC/24

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 112 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/16/100-240

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/16/24

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/16/BAC/100-240

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/16/BAC/24

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/16/LAN/100-240

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/16/LAN/24

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/16/LAN/BAC/100-240

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/16/LAN/BAC/24

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, fixed I/O
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/96/100-240

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/96/24

Trend IQ3 Web Enabled Controllers

The IQ3 controllers are Building Management System controllers that use Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/96/BAC/100-240

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/96/BAC/24

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/96/LAN/100-240

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/96/LAN/24

Trend IQ3 Trend LAN Controllers

The IQ3 Trend LAN controllers maintain all of the features of the IQ3XCITE range, however they use the Trend proprietary LAN for backward compatibility with IQ2 controllers. Each controller still incorporates a web server which, if Ethernet is connected, can deliver user specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server
Security protected monitor/control via web browser
Compatible with existing IQ system protocol
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/96/LAN/BAC/100-240

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 100..240Vac


IQ3XCITE/96/LAN/BAC/24

Trend IQ3 Trend LAN BACnet Controllers

The IQ3 Trend Lan BACnet controllers are Building Management System controllers that are compatible with the traditional IQ system protocol over the Trend LAN and use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world.
Network: Trend LAN
Features also include:
Trend Proprietary LAN main network for Backward compatibility to IQ2 controllers
Embedded web server with security protected monitor/control
BACnet over IP
I/O bus allows separate placement of I/O modules
MBus drivers (available through free download from Trend)
Modbus drivers (available through free download from Trend)
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Controllers, expandible to a maximum of 80 extra points or 15 I/O Modules
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/LAN/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/LAN/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Trend LAN/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/LAN/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/LAN/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Trend LAN/Ethernet
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: Trend LAN
Integration possible with: TCP/IP
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/SER/100-240

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/SER/24

Trend IQ3 Integration Controllers

The IQ3../.../XNC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
The product also includes:
All standard IQ3 features
Modbus drivers (free download from Trend website)
MBus drivers (free download from Trend website)

Ethernet/Serial
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/96/XNC/SER/BAC/100-240

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: 15 modules, 80 points
Power: 100..240Vac


IQ3XCITE/96/XNC/SER/BAC/24

Trend IQ3 BACnet Integration Controllers

The IQ3../.../XNC/BAC/... provides a flexible way of interfacing the IQ system with 3rd party systems. It utilises both standard IQ configuration modules, and the Trend Custom Language (TCL) to present information from other systems as though it were from an IQ controller. It also allows parameters within the 3rd party system to be adjusted from IQ system Supervisor and Tool software. The optional serial auxiliary board (/SER/) provides an additional RS232 or RS485 (2/4 wire) (or also RS422) port for communicating with other devices.
Flexible method of interfacing with 3rd party systems
BACnet over IP
Enhanced Custom Language (TCL)
Standard IQ configuration modules
Serial auxiliary board option (RS232 or RS485(2/4 wire))
All standard IQ3 features
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

Ethernet/Serial
UI: 10
DI: no
TI: no
AO: 6
DO: no
DOS: no
Network: TCP/IP
Integration possible with: RS232/RS485(2/4 wire)
Maximum expansion: 15 modules, 80 points
Power: 24Vac/24..60Vdc


IQ3XCITE/XML/UP

Trend IQ3 Web Enabled Controllers
Accessories

Upgrade to add XML services to IQ3xcite v2.2 or greater



IQ3xact/00/MSTP/BINC/100-240

Trend IQ3 BINC MSTP Router

The IQ3.../MSTP/BINC/... provides an interface between an MS/TP trunk (and its IQeco controllers) and the rest of the Trend Building Management System. It supports routing BACnet communications between TCP/IP and MS/TP networks. The unit also contains standard IQ3 functionality (e.g strategy), and provides virtual CNCs which allow supervisory or tool software running on PCs on the Ethernet network to connect to the Trend system.
Features also include:
Trend system interface with MS/TP trunk (IQecos).
Standard IQ configuration modules.
BACnet IP to MS/TP router.
MS/TP option board with terminator.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Network: MSTP

IQ3 BINC MSTP Router / Controller
Model: BACnet IP to MSTP router with no I/O capability.
Power: 230Vac


IQ3xact/00/MSTP/BINC/100-240

Trend IQeco35 controller
Accessories

Web enabled controller with no inputs or outputs, non expandable by the I/O bus. 100 to 240 Vac input power supply. Includes MSTP/BINC option.



IQ3xact/00/MSTP/BINC/24

Trend IQ3 Web Enabled BACnet Controllers

The IQ3 BACnet controllers are Building Management System controllers that use BACnet protocol over Ethernet and TCP/IP networking technologies. Each controller incorporates a web server which can deliver user-specific web pages to a PC or mobile device running internet browser software. If a system is set up with the correct connections, a user with the appropriate security codes can monitor or adjust the controller from any Internet access point in the world. It is also compatible with the traditional IQ system protocol.
Network: TCP/IP
The following features are also available:
Ethernet 10 Mbps main network with TCP/IP protocol
Embedded web server with security protected monitor/control
BACnet over IP
MSTP routing capability with IQ3xact/.../MSTP/BINC
Compatible with existing IQ system protocol
I/O bus allows separate placement of I/O modules
Flexible number of software strategy modules
100 to 240 Vac, or 24 Vac and 24 to 60 Vdc input power supply versions
Small footprint with DIN rail mounting
This selection tool is designed to be used as a guide, please ratify any selections made prior to ordering your IQ3xcite equipment.
This tool does not calculate any additional power supplies required for the i/o modules. Please refer to the requirements for powering the modules as stipulated in the IQ3xcite training course.
The IQ3xcite Points Calculator aims to calculate the controllers and modules required in the most cost effective manner. In cases this may mean that modules are fitted to the controller where some points on those modules cannot be connected within the controller firmware. In such cases we suggest the connectors are removed or other indication is made.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI.

BINC Controllers, fixed I/O, MSTP routing capability
UI: no
DI: no
TI: no
AO: no
DO: no
DOS: no
Power: 24Vac/24..60Vdc


IQ3xact/00/MSTP/BINC/24

Trend IQeco35 controller
Accessories

Web enabled controller with no inputs or outputs, non expandable by the I/O bus. 24 Vac or 24 to 36 Vdc input power supply. Includes MSTP/BINC option.



IQ3xact/12/MSTP/BINC/100-240

Trend IQ3 BINC MSTP Router

The IQ3.../MSTP/BINC/... provides an interface between an MS/TP trunk (and its IQeco controllers) and the rest of the Trend Building Management System. It supports routing BACnet communications between TCP/IP and MS/TP networks. The unit also contains standard IQ3 functionality (e.g strategy), and provides virtual CNCs which allow supervisory or tool software running on PCs on the Ethernet network to connect to the Trend system.
Features also include:
Trend system interface with MS/TP trunk (IQecos).
Standard IQ configuration modules.
BACnet IP to MS/TP router.
MS/TP option board with terminator.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Network: MSTP

IQ3 BINC MSTP Router / Controller
Model: BACnet IP to MSTP router with I/O capability on Trend/IP side.
Power: 230Vac


IQ3xact/12/MSTP/BINC/24

Trend IQ3 BINC MSTP Router

The IQ3.../MSTP/BINC/... provides an interface between an MS/TP trunk (and its IQeco controllers) and the rest of the Trend Building Management System. It supports routing BACnet communications between TCP/IP and MS/TP networks. The unit also contains standard IQ3 functionality (e.g strategy), and provides virtual CNCs which allow supervisory or tool software running on PCs on the Ethernet network to connect to the Trend system.
Features also include:
Trend system interface with MS/TP trunk (IQecos).
Standard IQ configuration modules.
BACnet IP to MS/TP router.
MS/TP option board with terminator.
BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards.
Network: MSTP

IQ3 BINC MSTP Router / Controller
Model: BACnet IP to MSTP router with I/O capability on Trend/IP side.
Power: 24Vac


IQE/PROG/UP

Trend IQeco31 controller
Accessories

Upgrade licence to convert a fixed strategy controller to a programmable controller.



IQE31/C/BAC/Custom/230

Trend IQeco31 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 31
Programability: Programmable
Control: Custom strategy


Power: 230V


IQE31/C/BAC/Custom/24VAC

Trend IQeco31 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 31
Programability: Programmable
Control: Custom strategy


Power: 24V


IQE31/F/BAC/1SFANAR2B/230

Trend IQeco31 FCU 1S Fan AR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/1SFANAR2B/24VAC

Trend IQeco31 FCU 1S Fan AR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/1SFANWR2B/230

Trend IQeco31 FCU 1S Fan WR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/1SFANWR2B/24VAC

Trend IQeco31 FCU 1S Fan WR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/1SFANWR4B/230

Trend IQeco31 FCU 1S Fan WR4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/1SFANWR4B/24VAC

Trend IQeco31 FCU 1S Fan WR4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/1SFANWT2B/230

Trend IQeco31 FCU 1S Fan WT2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/1SFANWT2B/24VAC

Trend IQeco31 FCU 1S Fan WT2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/1SFANWT4B/230

Trend IQeco31 1S FAN WT4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/1SFANWT4B/24VAC

Trend IQeco31 1S FAN WT4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/ECFANAR2P/230

Trend IQeco31 EC FAN AR2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/ECFANAR2P/24VAC

Trend IQeco31 EC FAN AR2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/ECFANWR2P/24VAC

Trend IQeco31 controller

The IQeco31 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. It has 10 I/O channels and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQeco. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 1
DI: 1
TI: 2
AO: 1
DO: 4
Relay outputs: 1
Power supply: 24Vac

Controllers
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Programability: Fixed


IQE31/F/BAC/ECFANWR4P/230

Trend IQeco31 EC FAN WR4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/ECFANWR4P/24VAC

Trend IQeco31 EC FAN WR4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/ECFANWT2P/230

Trend IQeco31 EC FAN WT2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/ECFANWT2P/24VAC

Trend IQeco31 EC FAN WT2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/ECFANWT4P/230

Trend IQeco31 EC Fan WT4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 230V


IQE31/F/BAC/ECFANWT4P/24VAC

Trend IQeco31 EC Fan WT4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Fixed
Power: 24V


IQE31/F/BAC/NOSTRATEGY/230

Trend IQeco31 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy


Programability: Fixed
Power: 230V


IQE31/F/BAC/NOSTRATEGY/24VAC

Trend IQeco31 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy


Programability: Fixed
Power: 24V


IQE31/P/BAC/1SFANAR2B/230

Trend IQeco31 FCU 1S Fan AR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/1SFANAR2B/24VAC

Trend IQeco31 FCU 1S Fan AR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/1SFANWR2B/230

Trend IQeco31 FCU 1S Fan WR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/1SFANWR2B/24VAC

Trend IQeco31 FCU 1S Fan WR2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/1SFANWR4B/230

Trend IQeco31 FCU 1S Fan WR4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/1SFANWR4B/24VAC

Trend IQeco31 FCU 1S Fan WR4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/1SFANWT2B/230

Trend IQeco31 FCU 1S Fan WT2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/1SFANWT2B/24VAC

Trend IQeco31 FCU 1S Fan WT2 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/1SFANWT4B/230

Trend IQeco31 1S FAN WT4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/1SFANWT4B/24VAC

Trend IQeco31 1S FAN WT4 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and on/off fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: 1 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/ECFANAR2P/230

Trend IQeco31 EC FAN AR2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/ECFANAR2P/24VAC

Trend IQeco31 EC FAN AR2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy also supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/ECFANWR2P/24VAC

Trend IQeco31 controller

The IQeco31 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. It has 10 I/O channels and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQeco. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 1
DI: 1
TI: 2
AO: 1
DO: 4
Relay outputs: 1
Power supply: 24Vac

Controllers
Application: EC fan
Control: Water/Raise/Lower/2 pipe
Programability: Programmable


IQE31/P/BAC/ECFANWR4P/230

Trend IQeco31 EC FAN WR4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/ECFANWR4P/24VAC

Trend IQeco31 EC FAN WR4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/ECFANWT2P/230

Trend IQeco31 EC FAN WT2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/ECFANWT2P/24VAC

Trend IQeco31 EC FAN WT2 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/2 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/ECFANWT4P/230

Trend IQeco31 EC Fan WT4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 230V


IQE31/P/BAC/ECFANWT4P/24VAC

Trend IQeco31 EC Fan WT4 P

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and electronically commutated fan, in response to a thermistor temperature sensor with a local setpoint knob and a local switch input (window contact, pushbutton, or Passive Infra Red movement detector input). The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 31
Application: EC fan
Control: Water/Thermic/4 pipe
Library: Lib.3: Plus
Units: Metric


Programability: Programmable
Power: 24V


IQE31/P/BAC/NOSTRATEGY/230

Trend IQeco31 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy


Programability: Programmable
Power: 230V


IQE31/P/BAC/NOSTRATEGY/24VAC

Trend IQeco31 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 31
Control: No strategy


Programability: Programmable
Power: 24V


IQE35/C/BAC/CUSTOM/24VAC

Trend IQeco35 controller

The IQeco35 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. It has 17 I/O channels, and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQeco. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 3
DI: 2
TI: 3
AO: 1
DO: 4
Relay outputs: 4
Auxiliary output signal: 1 x 24 Vdc
Power supply: 24Vac

Controllers
Application: no
Control: Custom strategy
Programability: Fixed
Additional functions: no


IQE35/C/BAC/Custom/230

Trend IQeco35 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 35
Programability: Programmable
Control: Custom strategy


Power: 230V


IQE35/C/BAC/Custom/24VAC

Trend IQeco35 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 35
Programability: Programmable
Control: Custom strategy


Power: 24V


IQE35/F/BAC/3SFANAR2AUXB/230

Trend IQeco35 FCU 3S FAN AR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANAR2AUXB/24VAC

Trend IQeco35 FCU 3S FAN AR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANAR2E/230

Trend IQeco35 FCU 3S Fan AR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANAR2E/24VAC

Trend IQeco35 FCU 3S Fan AR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANAR2E99B/230

Trend IQeco35 FCU 3S Fan AR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANAR2E99B/24VAC

Trend IQeco35 FCU 3S Fan AR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANAR2EB/230

Trend IQeco35 FCU 3S Fan AR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANAR2EB/24VAC

Trend IQeco35 FCU 3S Fan AR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR2AUXB/230

Trend IQeco35 FCU 3S Fan WR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR2AUXB/24VAC

Trend IQeco35 FCU 3S Fan WR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR2E/230

Trend IQeco35 FCU 3S Fan WR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR2E/24VAC

Trend IQeco35 FCU 3S Fan WR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR2E99B/230

Trend IQeco35 FCU 3S Fan WR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR2E99B/24VAC

Trend IQeco35 FCU 3S Fan WR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR2EB/230

Trend IQeco35 FCU 3S Fan WR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR2EB/24VAC

Trend IQeco35 FCU 3S Fan WR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR4AUXB/230

Trend IQeco35 FCU 3S Fan WR4 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR4AUXB/24VAC

Trend IQeco35 FCU 3S Fan WR4 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR4E/230

Trend IQeco35 FCU 3S Fan WR4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR4E/24VAC

Trend IQeco35 FCU 3S Fan WR4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR4E99B/230

Trend IQeco35 FCU 3S Fan WR4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR4E99B/24VAC

Trend IQeco35 FCU 3S Fan WR4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWR4EB/230

Trend IQeco35 FCU 3S Fan WR4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWR4EB/24VAC

Trend IQeco35 FCU 3S Fan WR4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT2AUXB/230

Trend IQeco35 FCU 3S Fan WT2 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT2AUXB/24VAC

Trend IQeco35 FCU 3S Fan WT2 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT2E/230

Trend IQeco35 FCU 3S Fan WT2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT2E/24VAC

Trend IQeco35 FCU 3S Fan WT2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT2E99B/230

Trend IQeco35 FCU 3S Fan WT2 E 99B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT2E99B/24VAC

Trend IQeco35 FCU 3S Fan WT2 E 99B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT2EB/230

Trend IQeco35 FCU 3S Fan WT2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT2EB/24VAC

Trend IQeco35 FCU 3S Fan WT2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT4AUXB/230

Trend IQeco35 3S FAN WT 4 AUXB

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT4AUXB/24VAC

Trend IQeco35 3S FAN WT 4 AUXB

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT4E/230

Trend IQeco35 3S FAN WT4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT4E/24VAC

Trend IQeco35 3S FAN WT4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT4E99B/230

Trend IQeco35 FCU 3S FAN WT4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT4E99B/24VAC

Trend IQeco35 FCU 3S FAN WT4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/F/BAC/3SFANWT4EB/230

Trend IQeco35 3S FAN WT4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 230V


IQE35/F/BAC/3SFANWT4EB/24VAC

Trend IQeco35 controller

The IQeco35 is a terminal unit controller for use with BACnet over MS/TP. It can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. It has 17 I/O channels, and can be supplied as a fixed or programmable unit, with Trend written strategies, custom strategies or no strategy.
The programmable units allow the strategy to be modified to meet specific project requirements whereas the fixed units can only be used with a Trend supplied strategy.
The strategy itself defines the units HVAC control method. Various Trend strategies are available and they are divided into three categories, Entry, Basic and Plus. The Entry category has less sophisticated strategies with a lower level of I/O control and the Plus category has more sophisticated strategies with the highest level of I/O control.
Trend provide a service to supply personal strategies preloaded into the IQeco. This can significantly reduce time on site by removing the need to download the same strategy to potentially several hundred controllers.
Units defined as No Strategy are supplied empty and can have strategies downloaded from SET.
UI: 3
DI: 2
TI: 3
AO: 1
DO: 4
Relay outputs: 4
Auxiliary output signal: 1 x 24 Vdc
Power supply: 24Vac

Controllers
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Programability: Fixed
Additional functions: Electrical heat at 1% demand


IQE35/F/BAC/NOSTRATEGY/230

Trend IQeco35 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy


Programability: Fixed
Power: 230V


IQE35/F/BAC/NOSTRATEGY/24VAC

Trend IQeco35 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy


Programability: Fixed
Power: 24V


IQE35/F/IQE35/F/BAC/3SFANWT4EB/24VAC

Trend IQeco35 3S FAN WT4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Fixed
Power: 24V


IQE35/P/BAC/3SFANAR2AUXB/230

Trend IQeco35 FCU 3S FAN AR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANAR2AUXB/24VAC

Trend IQeco35 FCU 3S FAN AR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANAR2E/230

Trend IQeco35 FCU 3S Fan AR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANAR2E/24VAC

Trend IQeco35 FCU 3S Fan AR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANAR2E99B/230

Trend IQeco35 FCU 3S Fan AR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANAR2E99B/24VAC

Trend IQeco35 FCU 3S Fan AR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANAR2EB/230

Trend IQeco35 FCU 3S Fan AR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANAR2EB/24VAC

Trend IQeco35 FCU 3S Fan AR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The AR2 strategy is for an airside unit controlling 1 raise/lower (floating point) damper actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Air/Raise/Lower/Damper: (AR2)
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR2AUXB/230

Trend IQeco35 FCU 3S Fan WR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR2AUXB/24VAC

Trend IQeco35 FCU 3S Fan WR2 AUX B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR2E/230

Trend IQeco35 FCU 3S Fan WR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR2E/24VAC

Trend IQeco35 FCU 3S Fan WR2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR2E99B/230

Trend IQeco35 FCU 3S Fan WR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR2E99B/24VAC

Trend IQeco35 FCU 3S Fan WR2 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR2EB/230

Trend IQeco35 FCU 3S Fan WR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR2EB/24VAC

Trend IQeco35 FCU 3S Fan WR2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR2 strategy is for waterside 2 pipe units controlling 1 raise/lower (floating point) valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR4AUXB/230

Trend IQeco35 FCU 3S Fan WR4 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR4AUXB/24VAC

Trend IQeco35 FCU 3S Fan WR4 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR4E/230

Trend IQeco35 FCU 3S Fan WR4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR4E/24VAC

Trend IQeco35 FCU 3S Fan WR4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR4E99B/230

Trend IQeco35 FCU 3S Fan WR4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR4E99B/24VAC

Trend IQeco35 FCU 3S Fan WR4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWR4EB/230

Trend IQeco35 FCU 3S Fan WR4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWR4EB/24VAC

Trend IQeco35 FCU 3S Fan WR4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WR4 strategy is for waterside 4 pipe units controlling 2 raise/lower (floating point) valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Raise/Lower/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT2AUXB/230

Trend IQeco35 FCU 3S Fan WT2 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT2AUXB/24VAC

Trend IQeco35 FCU 3S Fan WT2 Aux B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT2E/230

Trend IQeco35 FCU 3S Fan WT2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT2E/24VAC

Trend IQeco35 FCU 3S Fan WT2 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT2E99B/230

Trend IQeco35 FCU 3S Fan WT2 E 99B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT2E99B/24VAC

Trend IQeco35 FCU 3S Fan WT2 E 99B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT2EB/230

Trend IQeco35 FCU 3S Fan WT2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT2EB/24VAC

Trend IQeco35 FCU 3S Fan WT2 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT2 strategy is for waterside 2 pipe units controlling 1 thermic valve actuator. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/2 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT4AUXB/230

Trend IQeco35 3S FAN WT 4 AUXB

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT4AUXB/24VAC

Trend IQeco35 3S FAN WT 4 AUXB

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. It also controls an auxiliary relay based on the occupation state. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Auxillary relay
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT4E/230

Trend IQeco35 3S FAN WT4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT4E/24VAC

Trend IQeco35 3S FAN WT4 E

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.1: Entry
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT4E99B/230

Trend IQeco35 FCU 3S FAN WT4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT4E99B/24VAC

Trend IQeco35 FCU 3S FAN WT4 E99 B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 99%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 99% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/3SFANWT4EB/230

Trend IQeco35 3S FAN WT4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 230V


IQE35/P/BAC/3SFANWT4EB/24VAC

Trend IQeco35 3S FAN WT4 E B

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco standard strategy controls a fan coil units heat/cool outputs, and 3 speed fan, in response to a thermistor temperature sensor with a local setpoint knob and a local window contact input and a pushbutton, or Passive Infra Red movement detector input. The electric heater is enabled when the heating demand is greater than 5%. The WT4 strategy is for waterside 4 pipe units controlling 2 thermic valve actuators. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
Model: IQeco 35
Application: 3 speed fan
Control: Water/Thermic/4 pipe
Library: Lib.2: Basic
Additional functions: Electrical heat at 1% demand
Units: Metric


Programability: Programmable
Power: 24V


IQE35/P/BAC/NOSTRATEGY/230

Trend IQeco35 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy


Programability: Programmable
Power: 230V


IQE35/P/BAC/NOSTRATEGY/24VAC

Trend IQeco35 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 35
Control: No strategy


Programability: Programmable
Power: 24V


IQE38/C/BAC/Custom/230

Trend IQeco38 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 38
Programability: Programmable
Control: Custom strategy


Power: 230V


IQE38/C/BAC/Custom/24VAC

Trend IQeco38 Custom

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The IQeco can be supplied with a strategy written by the customer. Trend will supply the strategy already downloaded into a programmable IQeco controller saving time on site. For this option the customer strategy must be supplied with the order; Trend will not test the strategy it will only ensure that the strategy supplied with the order can be successfully loaded into the controller.
Model: IQeco 38
Programability: Programmable
Control: Custom strategy


Power: 24V


IQE38/F/BAC/NOSTRATEGY/230

Trend IQeco38 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy


Programability: Fixed
Power: 230V


IQE38/F/BAC/NOSTRATEGY/24VAC

Trend IQeco38 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy


Programability: Fixed
Power: 24V


IQE38/P/BAC/NOSTRATEGY/230

Trend IQeco38 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy


Programability: Programmable
Power: 230V


IQE38/P/BAC/NOSTRATEGY/24VAC

Trend IQeco38 No Strategy

The IQeco31, 35 and 38 are terminal unit controllers for use with BACnet over MS/TP. They can communicate with other IQecos over the BACnet MS/TP network, and with Trend networked devices by way of a BINC. They have from 10 to 18 I/O channels, and can be supplied either fully programmable or with a fixed strategy.
The IQeco can be purchased either as a fully programmable unit, or with a fixed strategy. The strategy defines its HVAC equipment interaction. Fixed strategy units can be reconfigured with a different strategy from a defined class of strategies within the strategy library.
The controllers can be supplied without a strategy, these are the "No Strategy" models. The programmable units /P/ can be engineered using SET and the fixed /F/ units can have a standard fixed strategy downloaded from SET.
Model: IQeco 38
Control: No strategy


Programability: Programmable
Power: 24V


IQEVAVP/P/BAC/VAV2E/24VAC

Trend IQeco VAV 2E

The IQeco variable air volume standard strategy controls a proportional damper, an on/off fan (either serial or parallel), and two stages of electric heating in response to a thermistor temperature sensor with a local setpoint knob. The 2E strategy is for on/off electric heating. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
The IQecoVAVP is fitted with a differentail air pressure transducer. The IQecoVAVPA is fitted with a differential air pressure transducer and an actuator.
Model: IQeco VAVP
Programability: Fixed
Application: VAV
Control: VAV 2 Stage Electric Heater
Units: Metric
Power: 24V


Additional functions: no


IQEVAVPA/P/BAC/VAV2E/24VAC

Trend IQeco VAV 2E

The IQeco variable air volume standard strategy controls a proportional damper, an on/off fan (either serial or parallel), and two stages of electric heating in response to a thermistor temperature sensor with a local setpoint knob. The 2E strategy is for on/off electric heating. The strategy is designed to work with TB/TS Trend Thermistor Room Sensors. The strategy supports the fitting of a WMB Room Display module without further configuration.
The IQecoVAVP is fitted with a differentail air pressure transducer. The IQecoVAVPA is fitted with a differential air pressure transducer and an actuator.
Model: IQeco VAVP
Programability: Fixed
Application: VAV
Control: VAV 2 Stage Electric Heater
Units: Metric
Power: 24V


Additional functions: Fitted Actuator


IQEYE/COLLECTOR/230

Trend IQ EYE Collector Node Controller

The IQ EYE Collector collects the data necessary for the IQ EYE Server to carry out the performance monitoring calculations.
Via its integrated EINC L It also enables IQ networks running on the IQ system current loop Lan, Ethernet, and LonWorks bus to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory/tool software running in PCs connected to the Ethernet network to connect to the BMS system.
Operation on LonWorks bus is achieved without the need for any LonWorks network management.
UK only requires IQ Assured service agreement to activate
Collection of data for IQ EYE Server.
Collection of loop, alarm, and commuication performance data from IQ1, IQ2, IQ3, and IQL controllers.
Integral modem for connection to internet.
Integration of IQ network on IQ system current loop Lan, Ethernet and LonWorks bus via integrated EINC L.
10/100 BASE-T interface.
Eight virtual CNCs for PC connection using Ethernet.
FLASH retains configured data during power fail.
Integration of IQL controllers into IQ system.
Connection to LonWorks bus with IqlTool 2 using virtual CNC.
DHCP Enabled.
Network: TCP/IP + LON + Trend LAN

Data Collectors
Power: 230Vac
Comments: IP40


IQEYE/COLLECTOR/24

Trend IQ EYE Collector Node Controller

The IQ EYE Collector collects the data necessary for the IQ EYE Server to carry out the performance monitoring calculations.
Via its integrated EINC L It also enables IQ networks running on the IQ system current loop Lan, Ethernet, and LonWorks bus to be integrated into a single network. It operates at the internetwork level, including the necessary support for WANs. It also provides virtual CNCs that allow supervisory/tool software running in PCs connected to the Ethernet network to connect to the BMS system.
Operation on LonWorks bus is achieved without the need for any LonWorks network management.
UK only requires IQ Assured service agreement to activate
Collection of data for IQ EYE Server.
Collection of loop, alarm, and commuication performance data from IQ1, IQ2, IQ3, and IQL controllers.
Integral modem for connection to internet.
Integration of IQ network on IQ system current loop Lan, Ethernet and LonWorks bus via integrated EINC L.
10/100 BASE-T interface.
Eight virtual CNCs for PC connection using Ethernet.
FLASH retains configured data during power fail.
Integration of IQL controllers into IQ system.
Connection to LonWorks bus with IqlTool 2 using virtual CNC.
DHCP Enabled.
Network: TCP/IP + LON + Trend LAN

Data Collectors
Power: 24Vac
Comments: IP42 NEMA3R


IQL ROUTER/230

Trend Network Cards Lon

The LINC, Lon Internetwork Node Controller, provides the means by which IQLs integrate with the IQ System proprietary current loop network. The LINC operates at the IQ System's internetwork.
The IQL Router for use with IQ System Devices only allows the connection of two communication channels, and the routing of LonTalk messages between them. It improves system reliability by physically isolating one channel from another, and by strategic positioning, can reduce the network traffic in selected channels.
The Lonworks Commissioning Interface (LCI/USB) is a portable LonWorks communications node enabling connection from a PC (via a USB port) to the LonWorks bus.

Other Lon Devices
Model: LON Router
Network: LON
Power: 230Vac
Comments: IP20


IQL ROUTER/24VAC

Trend Network Cards Lon

The LINC, Lon Internetwork Node Controller, provides the means by which IQLs integrate with the IQ System proprietary current loop network. The LINC operates at the IQ System's internetwork.
The IQL Router for use with IQ System Devices only allows the connection of two communication channels, and the routing of LonTalk messages between them. It improves system reliability by physically isolating one channel from another, and by strategic positioning, can reduce the network traffic in selected channels.
The Lonworks Commissioning Interface (LCI/USB) is a portable LonWorks communications node enabling connection from a PC (via a USB port) to the LonWorks bus.

Other Lon Devices
Model: LON Router
Network: LON
Power: 24Vac
Comments: IP20


IQL11+/AR2/230

Trend IQL11 Controllers

The IQL11+ is a terminal unit controller which can be networked using a LonWorks network. It can communicate with other IQLs and LonMark devices via the LonWorks network, and with IQ system networked devices via a 3XTEND/EINC L. It has 1 relay output (normally fan on/off), and 4 triac outputs (normally to control valves or dampers). It has 2 variable resistance inputs of which one is normally a thermistor temperature sensor. There is also a digital input for monitoring a manual button or alarm contact; it can also be used to connect a room display.
Network: LON
AI: 2
DI: 1
DO: 1
Triac: 4
Comments: analogue input: thermistor only

Controllers
Application: air side
Strategy: raise/lower
Power: 230Vac


IQL11+/AR2/24VAC

Trend IQL11 Controllers

The IQL11+ is a terminal unit controller which can